VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1425

DTC Code DTC Name
C1425 Open in Stop Light Switch Circuit

DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When IG1 terminal voltage is 9.5 V or more, an open in the stop light switch assembly input line continues for 0.3 seconds or more.

  • Wire harness or connector

  • Stop light switch assembly

  • Stop light control relay (STOP LP relay) (w/ Downhill assist control or dynamic radar cruise control)

  • Skid control ECU (brake actuator assembly)

WIRING DIAGRAM

A018K4PE01

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed. On
      Brake pedal released. Off
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  2. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select the Data List using the GTS.

      Click here


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch assembly ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      Stop Light SW

    4. Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (STP TERMINAL) Click here

    OK

  3. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Depress the brake pedal several times to test the stop light circuit.

    6. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1425 is not output. A
      DTC C1425 is output. B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A018LQJC83
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the A47 skid control ECU (brake actuator assembly) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
      A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

  5. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Check the stop light switch assembly.

      Click here

      OK
      The stop light switch assembly is normal.
      Result
      Result Proceed to
      OK (w/ Downhill assist control or dynamic radar cruise control) A
      OK (w/o Downhill assist control or dynamic radar cruise control) B
      NG C

    B

    CHECK HARNESS AND CONNECTOR (STP TERMINAL) Click here

    C

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    A

  6. CHECK HARNESS AND CONNECTOR (SWITCH INPUT TERMINAL)


    1. A018JPDC01
      *1 NO. 1 Engine Room Relay Block and NO. 1 Junction Block Assembly
      *2 Stop Light Control Relay (STOP LP Relay)

      Turn the ignition switch off.

    2. Remove the stop light control relay (STOP LP relay).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Stop light control relay (STOP LP relay) terminal 4 - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
      Stop light control relay (STOP LP relay) terminal 4 - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SWITCH INPUT CIRCUIT)

    OK

  7. INSPECT STOP LIGHT CONTROL RELAY


    1. A018IJLC15
      *1 Stop Light Control Relay (STOP LP Relay)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
      3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STOP LIGHT CONTROL RELAY

    OK

  8. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A018LQJC83
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Turn the ignition switch off.

    2. Install the stop light control relay (STOP LP relay).

    3. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    4. Disconnect the A47 skid control ECU (brake actuator assembly) connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
      A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

    OK

  9. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Reconnect the A47 skid control ECU (brake actuator assembly) connector.

    3. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the ignition switch off.

    5. Start the engine.

    6. Depress the brake pedal several times to test the stop light circuit.

    7. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1425 is not output. A
      DTC C1425 is output. B

      Tech Tips


      • If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).

        Click here

      • If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

        Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) Click here

  10. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A018LQJC83
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A47 skid control ECU (brake actuator assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A47-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
      A47-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

    OK

  11. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Reconnect the A47 skid control ECU (brake actuator assembly) connector.

    3. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the ignition switch off.

    5. Start the engine.

    6. Depress the brake pedal several times to test the stop light circuit.

    7. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1425 is not output. A
      DTC C1425 is output. B

      Tech Tips


      • If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).

        Click here

      • If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

        Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) Click here