VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1381

DTC Code DTC Name
C1381 Acceleration Sensor Power Supply Voltage Malfunction

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the acceleration sensor (airbag ECU assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.

These DTCs are also output when calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1381 Acceleration Sensor Power Supply Voltage Malfunction At a vehicle speed of more than 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.

  • Acceleration sensor (airbag ECU assembly)

  • Wire harness or connector

WIRING DIAGRAM

A0027SOE80

CAUTION / NOTICE / HINT

Note


  • When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)


    1. A0027W5C33
      *a

      Front view of wire harness connector

      (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the F38 yaw rate and acceleration sensor (airbag sensor assembly) connector.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F38-21 (IG2) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

    OK

  2. CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    1. A0027W5C34
      *a

      Front view of wire harness connector

      (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

      Turn the ignition switch off.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F38-25 (E1) - Body ground Always Below 1 Ω
      F38-26 (E2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

    OK

  3. RECONFIRM DTC


    1. Reconnect the F38 yaw rate and acceleration sensor (airbag sensor assembly) connector.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Perform a road test.

    6. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1381 is not output. A
      DTC C1381 is output B

      Note

      Check the yaw rate and acceleration sensor signal after replacement.

      Click here

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE AIRBAG SENSOR ASSEMBLY Click here