VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1413, C1414

DTC Code DTC Name
C1413 Front Speed Sensor RH Output Malfunction
C1414 Front Speed Sensor LH Output Malfunction

DESCRIPTION

Each speed sensor detects the wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS.

The speed sensor rotors have 48 serrations. Hall IC type speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.

A002BDQE27

Tech Tips

Check the connection status between the sensor connector and the vehicle wire harness.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1413 Front Speed Sensor RH Output Malfunction

Any of the following is detected:


  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.

  • Front speed sensor RH

  • Speed sensor circuit

  • Sensor installation

  • Front speed sensor rotor RH (front drive shaft assembly RH)

  • Skid control ECU (brake actuator assembly)
C1414 Front Speed Sensor LH Output Malfunction

Any of the following is detected:


  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.

  • Front speed sensor LH

  • Speed sensor circuit

  • Sensor installation

  • Front speed sensor rotor LH (front drive shaft assembly LH)

  • Skid control ECU (brake actuator assembly)

Tech Tips

for C1413 and C1414: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.


  1. Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

  2. Clear the DTCs.

DTC C1413 is for the front speed sensor RH.

DTC C1414 is for the front speed sensor LH.

WIRING DIAGRAM

A002BX7E92
*a Front Speed Sensor RH
*b Front Speed Sensor LH
*c Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)


    1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

      Click here


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Speed Open Front speed sensor RH open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -
      FL Speed Open Front speed sensor LH open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      FR Speed Open
      FL Speed Open
      OK
      There are no momentary interruptions.

      Tech Tips

      Perform the above inspection before removing the sensor and connector.

      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 4 Click here

    OK

  2. READ VALUE USING GTS (FRONT SPEED SENSOR)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Start the engine.

    4. Select the Data List using the GTS.

      Click here


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      FR Wheel Speed
      FL Wheel Speed

    5. Check the speed value output from the speed sensor displayed on the GTS.

      Tech Tips

      Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

      Click here

      OK
      The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FRONT SPEED SENSOR INSTALLATION Click here

    OK

  3. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Perform a road test.

    6. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1413 and C1414 are not output. A
      DTCs C1413 and/or C1414 are output. B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  4. CHECK FRONT SPEED SENSOR INSTALLATION


    1. Turn the ignition switch off.

    2. A002B8KC10
      *1 Front Speed Sensor
      *a Correct
      *b Incorrect
      *c 8.5 N*m
      *d No clearance

      Check the speed sensor installation.

      OK
      There is no clearance between the sensor and front steering knuckle.
      The installation bolt is tightened properly.
      Torque
      8.5 N*m (87 kgf*cm, 75 in.*lbf)
      Result
      Proceed to
      OK
      NG

    NG

    INSTALL FRONT SPEED SENSOR CORRECTLY Click here

    OK

  5. CHECK FRONT SPEED SENSOR AND SENSOR ROTOR


    1. Remove the front speed sensor and the component with the sensor rotor.

      for speed sensor: Click here

      for sensor rotor (for 1AR-FE): Click here

      for sensor rotor (for 2GR-FKS): Click here

    2. Check the speed sensor tip and speed sensor rotor.

      OK
      No scratches, oil, or foreign matter on the sensor tip and rotor.

      Note


      • If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

        If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

      • Check the speed sensor signal after cleaning or replacement.

        Click here

      Result
      Proceed to
      OK
      NG

    NG

    CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)


    1. Install the front speed sensor and the component with the sensor rotor.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the A86 skid control ECU (brake actuator assembly) connector.

    4. Disconnect the A35 or A34 front speed sensor connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      A86-31 (FR+) - A35-2 (FR+) Always Below 1 Ω
      A86-31 (FR+) or A35-2 (FR+) - Body ground Always 10 kΩ or higher
      A86-30 (FR-) - A35-1 (FR-) Always Below 1 Ω
      A86-30 (FR-) or A35-1 (FR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      A86-18 (FL+) - A34-2 (FL+) Always Below 1 Ω
      A86-18 (FL+) or A34-2 (FL+) - Body ground Always 10 kΩ or higher
      A86-17 (FL-) - A34-1 (FL-) Always Below 1 Ω
      A86-17 (FL-) or A34-1 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)


    1. A0027ZXC36
      *A RH
      *B LH
      *a

      Front view of wire harness connector

      (to Front Speed Sensor)

      Reconnect the A86 skid control ECU (brake actuator assembly) connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for RH
      Tester Connection Condition Specified Condition
      A35-2 (FR+) - Body ground Ignition switch ON 5.7 to 14 V
      for LH
      Tester Connection Condition Specified Condition
      A34-2 (FL+) - Body ground Ignition switch ON 5.7 to 14 V

      Note

      Check the speed sensor signal after replacement.

      Click here

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT SPEED SENSOR Click here

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here