FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for 2GR-FKS) COMPONENTS
ILLUSTRATION
| *1 | OUTER COWL TOP PANEL SUB-ASSEMBLY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COOL AIR INTAKE DUCT SEAL | *2 | FRONT FENDER APRON SEAL LH |
| *3 | FRONT FENDER APRON SEAL RH | *4 | FRONT FENDER LINER LH |
| *5 | FRONT FENDER LINER RH | *6 | FRONT FLOOR COVER LH |
| *7 | NO. 1 ENGINE UNDER COVER | *8 | NO. 2 ENGINE UNDER COVER |
| *9 | RADIATOR SIDE DEFLECTOR SEAL LH | *10 | RADIATOR SIDE SEAL RH |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE | *2 | BATTERY |
| *3 | BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY | *4 | ENGINE WIRE |
| *5 | INLET AIR CLEANER ASSEMBLY | *6 | V-BANK COVER SUB-ASSEMBLY |
| *7 | BATTERY TRAY | *8 | BATTERY CLAMP |
| *9 | BATTERY CLAMP BOLT | *10 | NO. 1 FUEL VAPOR FEED HOSE |
| *11 | NO. 2 VENTILATION HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | AIR SURGE TANK TO INTAKE MANIFOLD GASKET | *2 | INTAKE AIR SURGE TANK ASSEMBLY |
| *3 | NO. 2 SURGE TANK STAY | *4 | PURGE VALVE (PURGE VSV) |
| *5 | THROTTLE BODY GASKET | *6 | THROTTLE BODY WITH MOTOR ASSEMBLY |
| *7 | VENTILATION HOSE | *8 | WIRE HARNESS CLAMP BRACKET |
| *9 | NO. 1 FUEL VAPOR FEED HOSE | *10 | VACUUM HOSE SUB-ASSEMBLY |
| *11 | NO. 2 AIR TUBE | *12 | NO. 2 WATER BY-PASS HOSE |
| *13 | NO. 3 WATER BY-PASS HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
| *3 | FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY | *4 | FRONT STABILIZER LINK ASSEMBLY LH |
| *5 | NO. 1 EXHAUST PIPE SUPPORT BRACKET | *6 | STEERING INTERMEDIATE SHAFT ASSEMBLY |
| *7 | STEERING LINK ASSEMBLY | *8 | TIE ROD ASSEMBLY LH |
| *9 | COTTER PIN | *10 | GASKET |
| *11 | WINDSHIELD WASHER JAR ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for 2WD | - | - |
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR RH |
| *3 | FRONT ENGINE MOUNTING INSULATOR ASSEMBLY | *4 | FRONT FRAME ASSEMBLY |
| *5 | HOLE PLUG | *6 | REAR ENGINE MOUNTING INSULATOR ASSEMBLY |
| *7 | TRANSMISSION OIL THERMOSTAT | *8 | FRAME SIDE RAIL PLATE LH |
| *9 | FRAME SIDE RAIL PLATE RH | *10 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *11 | FRONT SUSPENSION MEMBER REAR BRACE RH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for AWD | - | - |
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR RH |
| *3 | FRONT ENGINE MOUNTING INSULATOR ASSEMBLY | *4 | FRONT FRAME ASSEMBLY |
| *5 | FRONT NO. 1 STABILIZER BRACKET LH | *6 | FRONT NO. 1 STABILIZER BRACKET RH |
| *7 | FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY | *8 | HOLE PLUG |
| *9 | REAR ENGINE MOUNTING INSULATOR ASSEMBLY | *10 | STEERING LINK ASSEMBLY |
| *11 | TRANSMISSION OIL THERMOSTAT | *12 | FRAME SIDE RAIL PLATE LH |
| *13 | FRAME SIDE RAIL PLATE RH | *14 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *15 | FRONT SUSPENSION MEMBER REAR BRACE RH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 2WD | - | - |
| *1 | FRONT FRAME ASSEMBLY | *2 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
| *3 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH | *4 | FRONT NO. 1 STABILIZER BRACKET LH |
| *5 | FRONT NO. 1 STABILIZER BRACKET RH | *6 | FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY |
| *7 | STEERING LINK ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 2WD | *B | for AWD |
| *1 | FRONT FRAME ASSEMBLY | *2 | FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION |
| *3 | FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER | *4 | FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH |
| *5 | FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH | *6 | FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER |
| *7 | HOLE PLUG | *8 | NO. 2 FRAME CROSSMEMBER DYNAMIC DAMPER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |