REAR AXLE CARRIER(for 2WD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL LOWER CONTROL ARM PIN


    1. A002840N02

      Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

      Note

      Do not overtighten the vise.

    2. Using SST, install a new lower control arm pin to the rear axle carrier sub-assembly as shown in the illustration.

      SST
      09650-17011

  2. TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY


    1. Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

      Note

      Do not overtighten the vise.

    2. A002A4Y

      Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

      Tech Tips

      Pushing out the bushing makes it easier to install the rear axle carrier sub-assembly.

    3. A002BRKC01
      *a Wooden Block
      *b Jack

      Temporarily install the rear axle carrier sub-assembly to the rear No. 1 suspension arm assembly with the spacer and nut (A).

      Note

      Fully tighten the nut (A) after stabilizing the suspension.

    4. Install the rear axle carrier sub-assembly to the rear No. 2 suspension arm assembly with the bolt (B) and nut.

      Torque:
      100 N*m  { 1020 kgf*cm, 74 ft.*lbf }

      Note


      • Insert the bolt with the threaded end facing the front of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    5. Install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt (C) and nut.

      Torque:
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }

      Note


      • Insert the bolt with the threaded end facing the rear of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    6. Install the rear axle carrier sub-assembly to the rear lower shock absorber bracket sub-assembly with the 2 bolts (D).

      Torque:
      100 N*m  { 1020 kgf*cm, 74 ft.*lbf }

    7. Slowly lower the rear No. 2 suspension arm assembly.

  3. TEMPORARILY INSTALL PARKING BRAKE ASSEMBLY


    1. A002B1S

      Temporarily install the parking brake assembly to the rear axle carrier sub-assembly with the nut.

      Note


      • Do not twist the parking brake cable when installing the parking brake assembly.

      • Fully tighten the nut after installing the rear trailing arm assembly.

  4. INSTALL REAR TRAILING ARM ASSEMBLY

    Click here

  5. INSTALL PARKING BRAKE ASSEMBLY


    1. A002BVK

      Install the parking brake assembly with the nut.

      Torque:
      160 N*m  { 1632 kgf*cm, 118 ft.*lbf }

  6. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

    Click here

  7. INSTALL SKID CONTROL SENSOR WIRE

    Click here

  8. INSTALL REAR DISC

    Click here

  9. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
    2. A0029DH

      Install the rear flexible hose to the rear upper control arm assembly with the bolt.

      Torque:
      18.8 N*m  { 192 kgf*cm, 14 ft.*lbf }

      Note


      • Do not twist the rear flexible hose when installing it.

      • Do not damage the rear flexible hose when installing it.

      • If the rear flexible hose is damaged, replace it with a new one.

    3. A002BTIC02
      *1 Rear Brake Tube
      *2 Rear Flexible Hose
      B003Z8F Clip

      Install the rear flexible hose with a new clip.

      Note

      Install the clip as far as it will go.

    4. Using a union nut wrench, connect the rear flexible hose to the rear brake tube while holding the rear flexible hose with a wrench.

      Torque:
      15.2 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note


      • Do not kink or damage the brake line.

      • Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

        Click here

  11. BLEED BRAKE LINE

    Click here

  12. STABILIZE SUSPENSION

    Click here

  13. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. A002B99

      Install the rear No. 1 suspension arm assembly with the nut.

      Torque:
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }

  14. INSTALL REAR SUSPENSION ARM COVER

    Click here

  15. ADJUST PARKING BRAKE

    Click here

  16. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  17. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  18. CHECK FOR SPEED SENSOR SIGNAL

    Click here