REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

PROCEDURE


  1. DRAIN DIFFERENTIAL OIL

    Click here

  2. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH

    Click here

  3. REMOVE REAR DRIVE SHAFT ASSEMBLY LH

    Click here

  4. REMOVE REAR DRIVE SHAFT SNAP RING LH

    Click here

  5. TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH


    1. A0029HCC01
      *a Wooden Block
      *b Jack
      *c Spacer
      B003ZIE Bolt
      B003Z8F Nut

      Using a jack and wooden block, jack up the rear No. 2 suspension arm assembly LH to replicate standard vehicle height conditions.

      CAUTION:

      Do not jack up the rear No. 2 suspension arm assembly LH too high as the vehicle may fall.

    2. Temporarily install the rear axle carrier sub-assembly LH with the 4 bolts, 3 nuts and spacer to the rear No. 1 suspension arm assembly LH, rear No. 2 suspension arm assembly LH, rear upper control arm assembly LH and rear lower shock absorber bracket sub-assembly LH.

    3. Lower the jack.

  6. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

    Click here

  7. REMOVE REAR DRIVE SHAFT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

    Click here

  8. REMOVE REAR DRIVE SHAFT SNAP RING RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

    Click here

  9. TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  10. REMOVE NO. 2 ENGINE UNDER COVER

    Click here

  11. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

    Click here

  12. REMOVE TAIL EXHAUST PIPE ASSEMBLY

    Click here

  13. REMOVE STABILIZER LINK SUB-ASSEMBLY LH

    Click here

  14. REMOVE STABILIZER LINK SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

    Click here

  15. REMOVE REAR STABILIZER BAR

    Click here

  16. LOOSEN NO. 1 REAR DIFFERENTIAL SUPPORT

    Tech Tips

    Loosen the bolts only when removal of the No. 1 rear differential support is required.


    1. A002B8U

      Loosen the 2 bolts.

  17. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

    Note


    • Do not damage the contact surface when removing the rear differential carrier assembly with differential support.

    • The remaining oil may leak out when removing the rear differential carrier assembly with differential support.

    • Securely support the rear differential carrier assembly with differential support while performing this step to avoid excessively tilting or dropping the rear differential carrier assembly with differential support.

    • Remove the bolts and nuts with the rear differential carrier assembly with differential support secured.


    1. A0029TO

      Disconnect the vacuum hose from the electro magnetic control coupling sub-assembly.

    2. A002AHYC03
      *1 Lower Rear Differential Mount Stopper
      *a Attachment
      *b Engine Lifter

      Support the rear differential carrier assembly with differential support with an engine lifter using 3 attachments or equivalent tools as shown in the illustration.

    3. Remove the 2 bolts (A).

    4. Remove the 2 bolts (B), 2 nuts and 2 lower rear differential mount stoppers from the No. 1 rear differential support.

      Tech Tips

      The nuts have tabs to prevent them from rotating.

    5. A00295IC01
      *1 Vacuum Hose
      *2 Clamp
      *a Connector

      Slightly lower the rear differential carrier assembly with differential support, remove the vacuum hose from the 2 clamps, disconnect the connector, and remove the clamp from the connector bracket.

    6. Lower the rear differential carrier assembly with differential support slowly to remove the rear differential carrier assembly with differential support.

      Note

      Do not damage the vacuum hose and electro magnetic control coupling wire harness.

  18. REMOVE DIFFERENTIAL SUPPORT


    1. A00283M

      Remove the 3 bolts and rear differential support from the rear differential carrier assembly.

  19. REMOVE UPPER REAR DIFFERENTIAL MOUNT STOPPER


    1. A0029O0

      Remove the 2 upper rear differential mount stoppers from the No. 1 rear differential support.

  20. REMOVE NO. 1 REAR DIFFERENTIAL SUPPORT


    1. A002BFK

      Remove the 2 bolts, 2 nuts and No. 1 rear differential support.

      Tech Tips

      The nuts have tabs to prevent them from rotating.