REAR DIFFERENTIAL CARRIER ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | REAR DRIVE SHAFT ASSEMBLY LH | *2 | REAR DRIVE SHAFT ASSEMBLY RH |
| *3 | REAR DRIVE SHAFT SNAP RING LH | *4 | REAR DRIVE SHAFT SNAP RING RH |
| *5 | REAR STABILIZER BAR | *6 | STABILIZER LINK SUB-ASSEMBLY LH |
| *7 | STABILIZER LINK SUB-ASSEMBLY RH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Toyota genuine differential gear oil LT 75W-85 GL-5 or equivalent |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | for Front Side | *B | for Rear Side |
| *1 | FRONT CENTER FLOOR COVER | *2 | FRONT FLOOR COVER LH |
| *3 | NO. 2 ENGINE UNDER COVER | *4 | PROPELLER SHAFT GUARD |
| *5 | WIRING HARNESS CLAMP BRACKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | *T1 | for Type A: 32 (326, 24) for Type B: 10 (102, 7) |
ILLUSTRATION
| *1 | PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY | *2 | NO. 2 CENTER SUPPORT BEARING WASHER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Do not apply lubricants |
ILLUSTRATION
| *1 | TAIL EXHAUST PIPE ASSEMBLY | *2 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | DIFFERENTIAL INSPECTION PLUG | *2 | REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT |
| *3 | UPPER REAR DIFFERENTIAL MOUNT STOPPER | *4 | VACUUM HOSE |
| *5 | LOWER REAR DIFFERENTIAL MOUNT STOPPER | *6 | GASKET |
| *7 | REAR DIFFERENTIAL DRAIN PLUG | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CONNECTOR BRACKET | *2 | DIFFERENTIAL SUPPORT |
| *3 | NO. 1 REAR DIFFERENTIAL SUPPORT | *4 | CLAMP |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | DIAPHRAGM OIL SEAL | *2 | ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY |
| *3 | ELECTRO MAGNETIC CONTROL COUPLING WIRE HARNESS | *4 | REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| *5 | REAR DIFFERENTIAL DUST DEFLECTOR | *6 | REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
| *7 | REAR DRIVE PINION NUT | *8 | STRAIGHT PIN |
| *9 | STUD BOLT | *10 | TRANSMISSION COUPLING CONICAL SPRING WASHER |
| *11 | TRANSMISSION COUPLING SPACER | *12 | REAR DIFFERENTIAL CARRIER ASSEMBLY |
| *13 | CLAMP | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with SST |
| ● | Non-reusable part | |
MP grease |
 |
Hypoid gear oil LSD | - | - |
ILLUSTRATION
| *1 | DIFFERENTIAL SIDE BEARING RETAINER | *2 | REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG |
| *3 | REAR DIFFERENTIAL FILLER PLUG | *4 | REAR DRIVE SHAFT OIL SEAL LH |
| *5 | REAR DRIVE SHAFT OIL SEAL RH | *6 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | DIFFERENTIAL DRIVE PINION | *2 | DIFFERENTIAL RING GEAR |
| *3 | REAR DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR | *4 | REAR DIFFERENTIAL CASE BEARING |
| *5 | REAR DIFFERENTIAL DRIVE PINION BEARING SPACER | *6 | REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
| *7 | STRAIGHT PIN | *8 | REAR DIFFERENTIAL CASE SUB-ASSEMBLY |
| *9 | REAR DIFFERENTIAL CARRIER | *10 | REAR DIFFERENTIAL DRIVE PINION PLATE WASHER |
| *11 | REAR DIFFERENTIAL SIDE GEAR SHAFT PLATE WASHER | *12 | REAR DIFFERENTIAL CASE ASSEMBLY |
| *13 | REAR DIFFERENTIAL CASE BOLT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1360K | - | - |