FRONT SEAT ASSEMBLY(for Power Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY


    1. B00400A

      Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.

  2. INSTALL SEAT ADJUSTER COVER CAP


    1. B00407Y

      Install the 2 seat adjuster cover caps.

  3. INSTALL FRONT SEAT WIRE


    1. Connect each connector and engage each clamp to install the front seat wire.

  4. INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)


    1. B003ZB7

      Engage the 3 claws and guide to install the LH seat front seat cushion edge protector LH.

  5. INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)


    1. B003Z1B

      Engage the 3 claws and guide to install the RH seat front seat cushion edge protector LH.

  7. INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)

    Tech Tips

    Use the same procedure as for the LH side.

  8. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    1. B003Z3L

      Engage the clip to install the front seat lower cushion shield LH.

    2. Engage the hook as shown in the illustration.

    3. Install the screw.

  9. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

    Tech Tips

    Use the same procedure as for the LH side.

  10. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)


    1. B003ZIL

      Engage the 2 hooks to install the seat cushion climate control blower assembly.

    2. B003ZII

      Connect the connector.

  11. INSTALL SEAT CUSHION CLIMATE CONTROL BRACKET (w/ Climate Control Seat System)


    1. B003Z0H

      Install the seat cushion climate control bracket to the seat cushion climate control blower assembly with the 2 screws.

  12. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)


    1. B003ZMR

      Engage the 2 claws to install the seat cushion climate control duct to the seat cushion climate control blower assembly.

  13. INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY RH (for Front Passenger Side)


    1. w/ Front Seat Airbag Sub-assembly RH

      Click here

  14. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

    Click here

  15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. w/o Variable Seat Cushion System:


      1. B00401S

        Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. B003ZDT

        Using hog ring pliers, install 5 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    2. w/ Variable Seat Cushion System:


      1. B00401S

        Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. B003Z9A

        Using hog ring pliers, install 2 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

  16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Driver Side)


    1. B003Z1F

      w/o Variable Seat Cushion System:


      1. Engage the 10 hooks to install the separate type front seat cushion cover with pad.

    2. w/ Variable Seat Cushion System:


      1. B003Z3N

        Using hog ring pliers, install the separate type front seat cushion cover with pad with 4 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. B003ZSG

        Return the separate type front seat cushion cover with pad to its original position.

      3. B003ZT8

        Engage the 6 hooks.

      4. B003ZJE

        Engage the 4 hooks.

      5. B003ZJS

        Engage the 4 hooks.

      6. B00409DC01
        B003ZQH Fastener

        Engage the 2 fasteners.

    3. w/ Seat Heater System:


      1. B003ZIP

        Engage the 3 clamps.

  17. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Front Passenger Side)


    1. B003ZQ8

      Engage the 12 hooks and 2 clips to install the separate type front seat cushion cover with pad.

    2. w/ Seat Heater System:


      1. B003Z63

        Engage the 3 clamps.

    3. B003ZM8

      Engage the claw to install the connector.

  18. INSTALL FRONT SEAT NO. 2 WIRE


    1. Connect each connector and engage each clamp to install the front seat No. 2 wire.

  19. INSTALL FRONT SEATBACK HOOK


    1. for Driver Side


      1. Install the 2 front seatback hooks to the lumbar support adjuster assembly.

    2. for Front Passenger Side


      1. Install the 2 front seatback hooks to the front seatback spring sub-assembly.

  20. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Driver Side)

    Click here

  21. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (for Front Passenger Side)


    1. B003YXF

      Engage the 2 guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly.

    2. Engage the 2 claws.

  22. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. B003ZC6

      Engage each claw to install the 2 front seatback edge protectors.

  23. INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. B003YWM

      Engage the 4 hooks to install the seatback climate control blower.

    2. B00402L

      Install the clip.

    3. Connect the connector.

  24. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    Click here

  25. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

    Click here

  26. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. B00403P

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    2. B003ZT5

      Using hog ring pliers, install 4 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  27. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Install the separate type front seatback cover with pad.

  28. INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY


    1. B003Z6D

      Engage each claw to install the 2 front seat headrest support assemblies.

    2. w/ Climate Control Seat System:


      1. B004035

        Engage the 2 claws to connect the seatback climate control blower to the separate type front seatback pad.

    3. B003ZMTC01
      *a Bracket

      Engage the 3 brackets and install the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the brackets securely.

    4. B003ZNA

      Return the separate type front seatback cover to its original position.

    5. B003Z4Q

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    6. B003YYA

      Using hog ring pliers, install 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    7. B00408O

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  29. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    1. B003ZG2

      Engage the 4 guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.

    2. Install the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. w/ Seat Heater System:


      1. B003ZG5

        Engage the clamp.

      2. Connect the connector.

    4. B003Z46

      Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.

    5. B003ZE8C01
      B003ZQH Fastener

      Engage the fastener to secure the front seat airbag assembly wire harness.

    6. B003ZBD

      Engage the clamp.

    7. Connect the connector.

    8. B003Z6U

      Engage the 2 hooks.

  30. INSTALL SEAT VARIABLE CUSHION SWITCH (w/ Variable Seat Cushion System)

    Click here

  31. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side)

    Click here

  32. INSTALL FRONT POWER SEAT SWITCH (w/o Seat Position Memory System)

    Click here

  33. INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Position Memory System)

    Click here

  34. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B003ZBY

      Engage the 4 claws to install the reclining power seat switch knob.

  35. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B003Z8Z

      Engage the 4 claws to install the slide and vertical power seat switch knob.

  36. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD


    1. B003ZCD

      Engage the clamp.

    2. B003ZVL

      Engage the claw and clip to install the front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. w/ Variable Seat Cushion System:


      1. B003Z6G

        Engage the hook.

  37. INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)


    1. w/ Variable Seat Cushion System:


      1. B003ZU8

        Connect the connector to the variable cushion switch.

    2. B003ZSH

      Connect the connector to the front lumbar power seat switch.

    3. B003ZRD

      w/o Seat Position Memory System:


      1. Connect the connector to the front power seat switch.

    4. B00406I

      w/ Seat Position Memory System:


      1. Connect the 2 connectors to the position control ECU and switch assembly.

    5. B00408AC01
      B003ZIE Wire Harness Guide

      Install the wire harness to the wire harness guide.

    6. Engage the 2 clamps.

    7. B003Z6V

      Engage the 3 claws to close the wire harness cover.

    8. B003ZWZ

      Engage the guide.

    9. B003ZF1

      Engage the claw and 3 guides.

    10. B003Z2P

      Engage the guide.

    11. B003Z0S

      Engage the 2 claws and clip to install the front seat cushion shield.

    12. B003Z6F

      Engage the claw.

  38. INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)


    1. B003ZBR

      Connect the connector to the front power seat switch.

    2. B003ZA0C01
      B003ZIE Wire Harness Guide

      Install the wire harness to the wire harness guide.

    3. Engage the 2 clamps.

    4. B00403C

      Engage the 3 claws to close the wire harness cover.

    5. B003ZQ6

      Engage the guide.

    6. B00404Y

      Engage the claw and 4 guides.

    7. B003ZJW

      Engage the guide.

    8. B003ZS6

      Engage the 2 claws and clip to install the front seat cushion shield.

    9. B003Z6I

      Engage the claw.

  39. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)


    1. B00406H

      Engage the claw and guide to install the front seat inner cushion shield.

    2. B003ZD2

      Engage the claw and 3 guides.

  40. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)


    1. B003ZT6

      Engage the claw and guide to install the front seat inner cushion shield.

    2. B00405A

      Engage the claw and 4 guides.

  41. CONNECT SEPARATE TYPE FRONT SEATBACK COVER (w/o Climate Control Seat System)


    1. B003Z4V

      Connect the rubber band of the separate type front seatback cover.

  42. CONNECT SEPARATE TYPE FRONT SEATBACK COVER (w/ Climate Control Seat System)


    1. B003ZY7

      Engage the 2 hooks to connect the 2 rubber bands of the separate type front seatback cover.

  43. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

    Click here

  44. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

    Click here

  45. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

    Click here

  46. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here