REAR AIRBAG SENSOR INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL REAR AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A0029AYC01
      *a Correct *b Incorrect

    4. Insert the rear airbag sensor pin (stopper) into the body hole and install the rear airbag sensor to the vehicle body with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the rear airbag sensor pin (stopper) is securely inserted into the body hole.

      • Tighten the nut while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

    5. Connect the connector to the rear airbag sensor.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Be sure to engage the connector until it is locked (when locking, make sure that a click sound can be heard).

        A0028DCC15
        *a White Housing Lock *b Engage

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installed parts of the rear airbag sensor.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

    Click here

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

    Click here

  4. INSTALL ROPE HOOK

    Click here

  5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Click here

  6. INSTALL DECK TRIM POCKET COVER

    Click here

  7. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for RH Side)

    Click here

  8. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

    Click here

  9. INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (w/ Rear Automatic Air Conditioning System)

    Click here

  10. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY

    Click here

  11. INSTALL NO. 2 DECK SIDE TRIM COVER (for LH Side)

    Click here

  12. INSTALL NO. 1 DECK SIDE TRIM COVER (for RH Side)

    Click here

  13. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

    Click here

  14. INSTALL FRONT DECK SIDE TRIM COVER

    Click here

  15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

  16. INSTALL REAR DOOR SCUFF PLATE

    Click here

  17. INSTALL REAR OUTER SEAT TRACK BRACKET COVER

    Click here

  18. INSTALL REAR FLOOR FINISH PLATE

    Click here

  19. INSTALL REAR NO. 2 SEAT ASSEMBLY

    Click here

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  21. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  22. INSPECT SRS WARNING LIGHT

    Click here