METER / GAUGE SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus:


      1. for Combination Meter: Body Electrical / Combination Meter / Data List.

      2. for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.

      3. for Engine (for 1AR-FE): Powertrain / Engine and ECT / Data List.

      4. for Engine (for 2GR-FKS): Powertrain / Engine / Data List.

      5. for Main Body: Body Electrical / Main Body / Data List.

    7. Read the Data List according to the display on the GTS.


      1. Combination Meter


        Body Electrical > Combination Meter > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        ODO/TRIP Change SW ODO/TRIP switch OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        P-Seatbelt Buckle SW Front passenger seat belt buckle switch OFF or ON

        OFF: Front passenger seat belt fastened (seat belt warning light off)

        ON: Front passenger seat belt unfastened (seat belt warning light on)

        		 -
        Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
        Engine Rpm Engine speed Min.: 0 rpm, Max.: 12750 rpm Almost the same as actual engine speed -
        Coolant Temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up engine -
        Washer Switch Washer fluid level warning switch OFF or ON

        OFF: Washer fluid level not low

        ON: Washer fluid level low

        		 -
        Light Control Switch Light control switch knob OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        +B Voltage Value Battery voltage Min.: 0 V, Max.: 25.5 V 11 to 14 V -
        Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L

        Fuel receiver gauge indicates F: 64.8 L

        Fuel receiver gauge indicates 3/4: 51.6 L

        Fuel receiver gauge indicates 1/2: 36.0 L

        Fuel receiver gauge indicates 1/4: 20.4 L

        Fuel receiver gauge indicates E: 7.2 L

        		 Unit: Liter
        Ambient Temperature Outside temperature Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) Almost the same as actual outside temperature The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)
        Multi Switch (Up) Steering pad switch (Up) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Down) Steering pad switch (Down) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Menu) Steering pad switch (Top) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Enter) Steering pad switch (Enter) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Right) Steering pad switch (Right) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Left) Steering pad switch (Left) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        2nd-Row Seatbelt Buckle (R) Rear No. 1 RH seat belt buckle switch signal OFF or ON

        OFF: Rear No. 1 RH seat belt fastened

        ON: Rear No. 1 RH seat belt unfastened

        		 *
        2nd-Row Seatbelt Buckle (L) Rear No. 1 LH seat belt buckle switch signal OFF or ON

        OFF: Rear No. 1 LH seat belt fastened

        ON: Rear No. 1 LH seat belt unfastened

        		 *
        2nd-Row Seatbelt Buckle (C) Rear No. 1 center seat belt buckle switch signal OFF or ON

        OFF: Rear No. 1 center seat belt fastened

        ON: Rear No. 1 center seat belt unfastened

        		 *
        Oil Pressure Switch Oil pressure switch OFF or ON

        OFF: Engine started

        ON: Engine not started

        		 -
        Turn Signal Switch (Right) RH turn signal switch OFF or ON

        OFF: RH turn signal switch off

        ON: RH turn signal switch on

        		 -
        Turn Signal Switch (Left) LH turn signal switch OFF or ON

        OFF: LH turn signal switch off

        ON: LH turn signal switch on

        		 -
        Hazard Flasher Switch Hazard warning signal switch OFF or ON

        OFF: Hazard warning signal switch off

        ON: Hazard warning signal switch on

        		 -
        Turn Switch Signal (Full Turn) Turn switch signal OFF or ON

        OFF: LH or RH turn switch off

        ON: LH or RH turn switch on

        		 -
        Multi Switch (Back) Steering pad switch (Back) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Driver Side Seatbelt Warning Buzzer Condition of the driver seat belt warning buzzer OFF or ON

        OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

        ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

        		 Displays customize setting of driver side seat belt warning buzzer
        P-Seatbelt Warning Buzzer Condition of the front passenger seat belt warning buzzer OFF or ON

        OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when front passenger seat belt unfastened

        ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when front passenger seat belt unfastened

        		 Displays customize setting of front passenger side seat belt warning buzzer
        Rear Seatbelt Warning Buzzer Condition of the rear seat belt warning buzzer OFF or ON

        OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when rear seat belt unfastened

        ON: Seat belt warning buzzer sounds at vehicle speed of 20km/h (12 mph) or more when rear seat belt unfastened

        		 Displays customize setting of rear seat belt warning buzzer*
        ECO Drive Indicator Zone Condition of the eco driving indicator zone OFF or ON

        OFF: Eco driving indicator zone not displayed

        ON: Eco driving indicator zone displayed

        		 Displays customize setting of ECO drive indicator zone
        ODO Display Time After IG OFF Setting Condition of the ODO display time after the ignition switch is turned off 30s, 60s, 600s or OFF Displays customize setting of ODO display time after IG off setting -
        Lane Change Flashing Times Setting Condition of the lane change flashing times OFF, 3, 4, 5, 6 or 7 Displays customize setting of lane change flashing times setting -
        Flasher Sound Volume Adjustment Condition of the flasher sound volume adjustment Small, Medium or Large Displays customize setting of flasher sound volume adjustment -
        LDA System Existence of function With or Without

        With: w/ Lane departure alert system (w/ Steering Control)

        Without: w/o Lane departure alert system (w/ Steering Control)

        		 -
        PCS System Existence of function With or Without

        With: w/ Pre-collision system

        Without: w/o Pre-collision system

        		 -
        Radar Cruise System Existence of function With or Without

        With: w/ Dynamic radar cruise control system

        Without: w/o Dynamic radar cruise control system

        		 -
        Number of Trouble Code The number of the DTC currently stored Min.: 0, Max.: 255 0 -

        • *: w/ Rear Seat Belt Warning

      2. ABS/VSC/TRC


        Chassis > ABS/VSC/TRC > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

      3. Engine and ECT (for 1AR-FE)


        Powertrain > Engine and ECT > Data List
        Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
        Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 610 to 710 rpm: Idling Idling (engine warmed up and A/C off): 660 rpm When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
        Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up engine -

        This is the engine coolant temperature.

        Tech Tips


        • After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

        • After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

        • If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.

        • Check if the engine overheats when the value indicates higher than 135°C (275°F).

      4. Engine (for 2GR-FKS)


        Powertrain > Engine > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 650 to 750 rpm: Idling (shift lever in N, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
        Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up

        This is the engine coolant temperature.

        Tech Tips


        • After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

        • After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

        • If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.

        • Check if the engine overheats when the value indicates higher than 135°C (275°F).

      5. Main Body


        Body Electrical > Main Body > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Light Sensor Illuminance Light sensor illuminance 0 to 8191 lx Value is output according to ambient light level -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Perform the Active Test according the display on the GTS.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Speed Meter Operation Speedometer OFF, 0, 40, 80, 120, 160 or 200

      There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)


        Reference km/h:

      • 40 → 41.3 to 45.8

      • 80 → 82.7 to 87.7

      • 120 → 124.0 to 129.0

      • 160 → 165.3 to 170.4

      • 200 → 206.7 to 211.7
      TachoMeter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 -
      Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -
      A/T Indicator Operation 1 Shift position indicator OFF, L, 2, 3, 4, D, N, R or P -
      A/T Indicator Operation 2 Shift position indicator OFF, 5, 6 or S -
      Indicat. Lamp Airbag SRS warning light OFF or ON -
      Driver Side Seat Belt Driver or front passenger seat belt warning light OFF or ON -
      Indicat. Lamp ABS ABS warning light OFF or ON -
      Indicat. Lamp Slip Slip indicator light OFF or ON -
      Indicat. Lamp Beam High beam indicator light OFF or ON -
      Indicat. Lamp Tail Tail indicator light OFF or ON -
      Indicat. Lamp Fr FOG Front fog indicator light OFF or ON -
      Indicat. Lamp Rr FOG Rear fog indicator light OFF or ON *2
      Indicat. Pre-Collision PCS warning light OFF or ON *3
      Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON *1
      Indicat. ECONO Eco driving indicator light OFF or ON -
      Indicat. Lamp Brake Brake warning light OFF or ON -
      Indicat. EPS EPS warning light OFF or ON -
      Master Warning Master warning light OFF or ON -
      Indicat. Downhill Assist Control Downhill assist control indicator light OFF or ON *5
      Indicat. VSC OFF VSC OFF indicator light OFF or ON -
      Indicat. 4WD Lock AWD lock indicator light OFF or ON *5
      Automatic High Beam Indicator Automatic high beam indicator light OFF or ON *3
      Check Engine Indicator MIL (Check engine warning light) OFF or ON -
      Water Temperature Meter Operation Engine coolant temperature receiver gauge OFF, LOW, NORMAL or HIGH -
      Meter Display 1 Multi-information display OFF or All -

      • *1: w/ Tire Pressure Warning System

      • *2: w/ Rear Fog Light

      • *3: w/ Forward Recognition Camera

      • *4: w/ TOYOTA Parking Assist-sensor System

      • *5: for AWD