LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Ignition switch ACC signal ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      		 "ON" is also displayed for this item when the ignition switch is ON.
      IG SW Ignition switch ON signal ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 "OFF" is also displayed for this item when the ignition switch is ACC.
      RR Door Courtesy SW Rear door courtesy light switch assembly RH signal ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch assembly LH signal ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      		 -
      Back Door Courtesy SW Back door courtesy light switch signal ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      Glass Hatch Courtesy Switch Back door glass courtesy light switch signal*2 ON or OFF

      ON: Glass hatch open

      OFF: Glass hatch closed

      		 -
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch assembly RH signal ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly LH signal ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal ON or OFF

      ON: Rear door RH unlocked

      OFF: Rear door RH locked

      		 -
      RL-Door Lock Pos SW Rear door LH unlock detection switch signal ON or OFF

      ON: Rear door LH unlocked

      OFF: Rear door LH locked

      		 -
      Interior Light Control Operation of the illuminated entry system OFF or ON Customized value is displayed Displayed only when All Data is selected.
      I/L ON W/Door Key Unlock Function that lights up the interior lights when the doors are unlocked OFF or ON Customized value is displayed Displayed only when All Data is selected.
      Lighting Time Lighting time of the delay control function (illuminated entry system) 15s, 7.5s or 30s Customized value is displayed Displayed only when All Data is selected.
      Room Light when Aprchd Function that lights up the interior lights when a key enters any actuation area*1 OFF or ON Customized value is displayed Displayed only when All Data is selected.
      I/L when ACC OFF Function that lights up the interior lights when the ignition switch is turned from ON or ACC to off OFF or ON Customized value is displayed Displayed only when All Data is selected.
      Light Control Function that lights up the ambient lights (while driving)*3 OFF or ON Customized value is displayed Displayed only when All Data is selected.
      Interior Illumination Light Function that lights up the ambient lights (always)*3 OFF or ON Customized value is displayed Displayed only when All Data is selected.

      • *1: w/ Smart Entry and Start System

      • *2: w/ Glass Hatch Opener System

      • *3: w/ Ambient Light


      Body Electrical > Back Door > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Courtesy SW Back door courtesy light switch signal ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Entry&Start* / Active Test.


      • *: w/ Smart Entry and Start System

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system*1 ON or OFF Perform the Active Test with interior light DOOR switch in the map light assembly turned on.
      Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF

      When performing this Active Test, turn on each interior lights.


      • ON: DOME CUT relay off (interior lights turn off)

      • OFF: DOME CUT relay on (interior lights turn on)
      Interior Illumination Light1 Ambient lights*2 ON or OFF

      Precondition for using the Active Test to turn lights on and off:


      • Ignition switch is turned off just before performing the Active Test.

      Preconditions for using the Active Test to check dimmer controlled illumination:


      • Engine running.

      • Shift lever is in any position other than P.

      • *1: Refer to Description for the lights that are controlled by the illuminated entry system.

        Click here

      • *2: w/ Ambient Light


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Power/Engine SW Light Engine switch illumination* OFF or ON

      When performing this Active Test, make sure the following condition is met:

      The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the ignition switch is ON or ACC, or the engine is running.

      • *: w/ Smart Entry and Start System