DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS), Diagnostic DTC:P057162

DTC Code DTC Name
P057162 Brake Switch "A" Signal Compare Failure

DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more.

  • Stop light switch assembly

  • Harness or connector

  • ECM

WIRING DIAGRAM

A002AMKE05

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)


    1. A00285TC03
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the A87 stop light switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A87-2 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A87-7 (B) - Body ground Always 11 to 14 V
      A87-6 (B) - Body ground Engine switch on (IG) 11 to 14 V
      A87-6 (B) - Body ground Engine switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the A43 ECM connector.

    2. Disconnect the A87 stop light switch assembly connector.

    3. Disconnect the A86 skid control ECU (brake actuator assembly) connector.

    4. Disconnect the F10 certification ECU (smart key ECU assembly) connector.

    5. Disconnect the F48 transmission floor shift assembly (shift lock control unit) connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A43-42 (ST1-) - A87-5 (L) Always Below 1 Ω
      A43-27 (STP) - A87-3 (L) Always Below 1 Ω
      A43-42 (ST1-) or A87-5 (L) - Body ground Always 10 kΩ or higher
      A43-27 (STP) or A87-3 (L) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR