CRUISE CONTROL SYSTEM Cruise Main Indicator Light Circuit

DESCRIPTION

The ECM illuminates the cruise control indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise control indicator illuminates when the cruise control system is turned on using the cruise control main switch (ON-OFF button). If a malfunction is detected, the cruise control indicator turns off and a warning message is displayed. The cruise control indicator circuit uses CAN communication. If the cruise control indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Check the cruise control indicator by performing the Active Test.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Meter Display 1 Multi-information display OFF or All Test possible at vehicle speed of 0 km/h (0 mph)

      Body Electrical > Combination Meter > Active Test
      Tester Display
      Meter Display 1
      Result
      Result Proceed to
      The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
      The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B

    B

    GO TO METER / GAUGE SYSTEM Click here

    A

  2. READ VALUE USING GTS


    1. Enter the following menus: Powertrain / Cruise Control*1 or Radar Cruise 1*2 / Data List.

    2. Read the Data List according to the display on the GTS.


      Powertrain > Cruise Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      CCS Ready M-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
      CCS Indicator M-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
      Cancel Switch Cruise control indicator status ON or OFF

      ON: Cruise control indicator illuminates

      OFF: Cruise control indicator turns off

      		 -

      Powertrain > Cruise Control > Data List
      Tester Display
      Main SW M-CPU
      CCS Ready M-CPU
      CCS Indicator M-CPU

      Powertrain > Radar Cruise1 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
      Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
      Cruise Indicator Cruise control indicator status ON or OFF

      ON: Cruise control indicator illuminates

      OFF: Cruise control indicator turns off

      		 -

      Powertrain > Radar Cruise1 > Data List
      Tester Display
      Cruise Ready Main-CPU
      Cruise Ready Sub-CPU
      Cruise Indicator

      • *1: for 1AR-FE

      • *2: for 2GR-FKS

      Result
      Result Proceed to
      The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF button). A
      The cruise control indicator does not illuminate but the Data List item Cruise Indicator changes according to the operation of the cruise control main switch (ON-OFF button). B
      The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control main switch (ON-OFF button). C

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    B

    REPLACE COMBINATION METER ASSEMBLY Click here

    C

    REPLACE ECM for 1AR-FE: Click here
    REPLACE ECM for 2GR-FKS: Click here