OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used engine oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used engine oil and used engine oil filters at designated disposal sites only.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean the oil pan drain plug.

    4. Install a new gasket to the oil pan drain plug.

    5. Install the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  2. REMOVE OIL FILTER CAP ASSEMBLY


    1. A002BLCC04
      *a Pipe
      *b Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A00298J

      Remove the oil filter drain plug from the oil filter cap assembly.

    3. A002863C03
      *1 Oil Filter Cap Assembly
      *2 O-ring
      *a Pipe

      Insert the pipe with hose into the oil filter cap assembly.

      Note

      Be sure to insert the pipe with the O-ring installed on the oil filter cap assembly.

      Tech Tips

      Place the hose end into a container before draining the engine oil from the hose.

    4. A002AWD

      Make sure that the engine oil is completely drained, and remove the pipe with hose and O-ring.

      Tech Tips

      Be sure to turn the pipe as shown in the illustration.

    5. A002BIAN02

      Using SST, remove the oil filter cap assembly.

      SST
      09228-06501
    6. A002A4TC05
      *1 Oil Filter Element
      *2 Oil Filter Cap Assembly
      *3 O-ring

      Remove the oil filter element and O-ring from the oil filter cap assembly.

      Note

      Do not use any tools to remove the O-ring in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.

  3. INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap assembly, the threads and O-ring groove.

    2. A002BFDC11
      *1 O-ring
      *a Correct
      *b Incorrect

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

      Note


      • Be sure to install the O-ring in the proper location, otherwise engine oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element in the oil filter cap assembly.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring of the oil filter cap assembly again.

      Note

      Make sure that the O-ring does not get caught between the parts.

    6. A002AZLC03
      *1 Oil Filter Cap Assembly
      *2 O-ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, install the oil filter cap assembly.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

      • Do not cross thread the oil filter cap assembly.

    7. A002AW2C03
      *1 O-ring

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

      Note

      Remove any dirt or foreign matter from the installation surface.

    8. Install the oil filter drain plug to the oil filter cap assembly.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Make sure that the O-ring does not get caught between the parts.

  4. ADD ENGINE OIL


    1. A002BHW

      Add clean engine oil and install the oil filler cap.

      Note

      Do not allow engine oil adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

      If engine oil is on the location indicated by the arrow, replace the belt tensioner.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      • 5W-30

      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40

      • 20W-50
      Standard Capacity:
      Item Specified Condition
      Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 Imp.qts)
      Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 Imp.qts)
      Dry fill 7.1 liters (7.5 US qts, 6.2 Imp.qts)

  5. INSPECT FOR ENGINE OIL LEAK


    1. Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.