DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM, Diagnostic DTC:C1299/99

DTC Code DTC Name
C1299/99 Cancellation of 4WD Control

DESCRIPTION

This DTC is output if the heat generated by the Electro magnetic control coupling sub-assembly exceeds a certain amount or if the estimated oil temperature of the transfer exceeds a certain amount while driving.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
C1299/99 Cancellation of 4WD Control

When either of the following conditions is met:


  • Condition that controls coupling calorific value is predefined value or more.

  • Condition that transfer oil temperature is predefined value or more.

  • Condition, size or tire pressure of the front or rear tires

  • Suspension and ball joint

  • Drive shaft

  • Propeller shaft

  • Electro magnetic control coupling sub-assembly

  • 4WD ECU assembly

 DTC stored

CAUTION / NOTICE / HINT

Tech Tips

Check the condition of each related circuit connector before troubleshooting.

Click here

PROCEDURE


  1. CHECK VEHICLE USAGE


    1. Check that there has been no unintended vehicle usage.

      OK
      There is no evidence of rough use (the vehicle has not been driven on damaged or snowy roads, etc. for a long time).
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FOR INTERMITTENT PROBLEMS Click here

    OK

  2. CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Check if the brake control system DTC is output.

      Click here


      Chassis > ABS/VSC/TRAC > Trouble Codes

    5. Read the DTCs using the GTS.

      Result
      Result Proceed to
      Only DTC C1299/99 is output A
      DTC C1299/99 and other DTCs (brake control system DTC) B

    B

    REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM) Click here

    A

  3. CHECK RELATED PART


    1. Check the condition, size and tire pressure of the front and rear tires.

    2. Inspect the suspension and ball joint, etc. for rattles.

    3. Inspect the drive shaft and propeller shaft rotation condition.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS

    OK

  4. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > Four Wheel Drive > Clear DTCs

    2. Start the engine.

    3. Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

      Click here


      Chassis > Four Wheel Drive > Trouble Codes
      Result
      Result Proceed to
      DTCs are output A
      DTCs are not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  5. REPLACE 4WD ECU ASSEMBLY


    1. Replace the 4WD ECU assembly.

      Click here

      Note

      When the 4WD ECU assembly is replaced with a new one, it is not necessary to perform calibration.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > Four Wheel Drive > Clear DTCs

    2. Start the engine.

    3. Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

      Click here


      Chassis > Four Wheel Drive > Trouble Codes
      Result
      Result Proceed to
      DTCs are output A
      DTCs are not output B

    A

    REPLACE ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY Click here

    B

    END