AUTOMATIC TRANSAXLE SYSTEM Transmission Control Switch Circuit

DESCRIPTION

When the shift lever is in S and it is moved toward "-" or "+", it is possible to select different shift ranges (1st through 6th ranges).

Moving the shift lever toward "+" increases the shift range by one, and moving the shift lever toward "-" decreases the shift range by one.

WIRING DIAGRAM

A0028FFE01

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

    5. In accordance with the display on the GTS, read the Data List.


      Powertrain > Engine > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Sports Shift Up SW Sport shift up switch status ON or OFF

      • ON: Shift lever held in "+" (up-shift)

      • OFF: Shift lever not held in "+" (up-shift)

      		 -
      Sports Shift Down SW Sport shift down switch status ON or OFF

      • ON: Shift lever held in "-" (down-shift)

      • OFF: Shift lever not held "-" (down-shift)

      		 -

      Powertrain > Engine > Data List
      Tester Display
      Sports Shift Up SW
      Sports Shift Down SW
      Result
      Result Proceed to
      Data display is not within Normal Condition range A
      Data display is within Normal Condition range B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  2. CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)


    1. A002868C13
      *a

      Front view of wire harness connector

      (to Transmission Control Switch)

      Disconnect the transmission control switch connector from transmission floor shift assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F46-3 (IG) - Body ground Ignition switch ON 11 to 14 V
      Ignition switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK POWER SOURCE CIRCUIT

    OK

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)


    1. A002868C13
      *a

      Front view of wire harness connector

      (to Transmission Control Switch)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F46-5 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)


    1. A002AFJC01
      *a

      Component without harness connected

      (Transmission Control Switch)

      Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F46-3 (IG) - F46-7 (S) Shift lever in S, "+" or "-" Below 1 Ω
      Shift lever not in S, "+" or "-" 10 kΩ or higher
      F46-2 (SFTU) - F46-5 (E)

      Shift lever held in "+"

      (Up-shift)

      		 Below 1 Ω
      Shift lever not held in "+" 10 kΩ or higher
      F46-1 (SFTD) - F46-5 (E)

      Shift lever held in "-"

      (Down-shift)

      		 Below 1 Ω
      Shift lever not held in "-" 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    1. Connect the transmission control switch connector.

    2. A002B3IC12
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A43-27 (S) - Body ground

      • Ignition switch ON

      • Shift lever in S, "+" or "-"

      		 11 to 14 V
      A43-27 (S) - Body ground

      • Ignition switch ON

      • Shift lever not in S, "+" or "-"

      		 Below 1 V

    5. Turn the ignition switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A43-42 (SFTU) - Body ground

      Shift lever held in "+"

      (Up-shift)

      		 Below 1 Ω
      Shift lever not held in "+" 10 kΩ or higher
      A43-43 (SFTD) - Body ground

      Shift lever held in "-"

      (Down-shift)

      		 Below 1 Ω
      Shift lever not held in "-" 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR