ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | COOL AIR INTAKE DUCT SEAL | *2 | FRONT FENDER APRON SEAL LH |
| *3 | FRONT FENDER APRON SEAL RH | *4 | FRONT FENDER LINER LH |
| *5 | FRONT FENDER LINER RH | *6 | FRONT FLOOR COVER LH |
| *7 | NO. 1 ENGINE UNDER COVER | *8 | NO. 2 ENGINE UNDER COVER |
| *9 | RADIATOR SIDE DEFLECTOR SEAL LH | *10 | RADIATOR SIDE SEAL RH |
ILLUSTRATION
| *1 | OUTER COWL TOP PANEL SUB-ASSEMBLY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE | *2 | BATTERY CLAMP BOLT |
| *3 | BATTERY CLAMP | *4 | BATTERY |
| *5 | BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY | *6 | INLET AIR CLEANER ASSEMBLY |
| *7 | RESERVOIR BRACKET | *8 | V-BANK COVER SUB-ASSEMBLY |
| *9 | BATTERY TRAY | *10 | NO. 1 FUEL VAPOR FEED HOSE |
| *11 | NO. 2 VENTILATION HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE MOVING CONTROL ROD | *2 | NO. 2 ENGINE MOUNTING STAY RH |
| *3 | ENGINE MOVING CONTROL ROD BRACKET | *4 | NO. 1 RELAY BLOCK COVER |
| *5 | ENGINE WIRE | *6 | AIR CLEANER BRACKET |
| *7 | EARTH WIRE | *8 | NO. 3 ENGINE MOUNTING STAY RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *C | for Type A | *D | for Type B |
| *1 | NO. 1 FUEL VAPOR FEED HOSE | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | NO. 1 RADIATOR HOSE | *4 | NO. 2 RADIATOR HOSE |
| *5 | DISCHARGE HOSE SUB-ASSEMBLY | *6 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *7 | TRANSMISSION OIL THERMOSTAT | *8 | UNION TO CHECK VALVE HOSE |
| *9 | WATER HOSE SUB-ASSEMBLY | *10 | NO. 2 FUEL PIPE CLAMP |
| *11 | NO. 1 FUEL PIPE CLAMP | *12 | NO. 1 TRANSMISSION OIL COOLER HOSE |
| *13 | OUTLET NO. 1 OIL COOLER HOSE | *14 | SUCTION HOSE SUB-ASSEMBLY |
| *15 | O-RING | *16 | NO. 3 WATER BY-PASS HOSE |
| *17 | NO. 4 WATER BY-PASS HOSE | *18 | NO. 3 EARTH WIRE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | COMPRESSION SPRING |
| *3 | NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Upper Side) | *4 | FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY |
| *5 | GASKET | *6 | NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FRONT DRIVE SHAFT ASSEMBLY | *2 | STEERING INTERMEDIATE SHAFT ASSEMBLY |
| *3 | FRONT STABILIZER LINK ASSEMBLY LH | *4 | FRONT SPEED SENSOR LH |
| *5 | TIE ROD ASSEMBLY LH | *6 | FRONT AXLE SHAFT NUT |
| *7 | COTTER PIN | *8 | FRONT FLEXIBLE HOSE |
| *9 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *A | for 2WD | *B | for AWD |
| *1 | FRONT DRIVE SHAFT ASSEMBLY LH | *2 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *3 | TRANSFER STIFFENER PLATE RH | *4 | NO. 1 DRIVE SHAFT BEARING BRACKET SETTING BOLT |
| *5 | FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side) | *6 | REAR ENGINE MOUNTING BRACKET |
| *7 | BEARING BRACKET HOLE SNAP RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for AWD | - | - |
| *1 | STEERING LINK ASSEMBLY | *2 | FRONT STABILIZER BAR |
| *3 | FRONT NO. 1 STABILIZER BRACKET LH | *4 | FRONT NO. 1 STABILIZER BRACKET RH |
| *5 | FRAME SIDE RAIL PLATE LH | *6 | FRAME SIDE RAIL PLATE RH |
| *7 | FRONT SUSPENSION MEMBER REAR BRACE LH | *8 | FRONT SUSPENSION MEMBER REAR BRACE RH |
| *9 | ENGINE ASSEMBLY WITH TRANSAXLE | *10 | ENGINE MOUNTING BRACKET RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 2WD | *B | for AWD |
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR RH |
| *3 | FRONT ENGINE MOUNTING INSULATOR ASSEMBLY | *4 | REAR ENGINE MOUNTING INSULATOR ASSEMBLY |
| *5 | FRONT FRAME ASSEMBLY | *6 | HOLE PLUG |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | AUTOMATIC TRANSAXLE ASSEMBLY | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | FLYWHEEL HOUSING UNDER COVER | *4 | MANIFOLD STAY |
| *5 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE | *6 | REAR DRIVE PLATE SPACER |
| *7 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | *8 | ENGINE WIRE |
| *9 | STARTER ASSEMBLY | - | - |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Adhesive 1324 |
| ★ | Precoated part | - | - |