ENGINE UNIT INSTALLATION

PROCEDURE


  1. INSTALL RADIATOR PIPE CLAMP


    1. Install the radiator pipe clamp to the camshaft housing sub-assembly LH with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  2. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

    2. Install the wire harness clamp bracket to the cylinder head cover LH with the bolt.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

    3. Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  3. INSTALL REAR ENGINE MOUNTING BRACKET (for 2WD)


    1. Install the rear engine mounting bracket to the cylinder block sub-assembly with the 3 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  4. INSTALL REAR ENGINE MOUNTING BRACKET (for AWD)


    1. Install the rear engine mounting bracket to the cylinder block sub-assembly with the 3 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  5. INSTALL NO. 5 CYLINDER BLOCK INSULATOR


    1. A002C8LC01
      *a Fastener Surface

      Install the No. 5 cylinder block insulator to the engine assembly.

      Note

      Make sure that the No. 5 cylinder block insulator is not covering any fastener surface.

  6. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Install a new engine oil level dipstick guide O-ring to the engine oil level dipstick guide.

    2. Apply a light coat of engine oil to the engine oil level dipstick guide O-ring.

    3. Insert the engine oil level dipstick guide end into the oil pan sub-assembly.

    4. Install the engine oil level dipstick guide to the camshaft housing sub-assembly LH with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    5. Install the engine oil level dipstick to the engine oil level dipstick guide.

  7. INSTALL WATER PUMP PULLEY

    Click here

  8. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    1. Install the V-ribbed belt tensioner assembly with the 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  9. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

    Click here

  10. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET


    1. A0029GZN01

      Install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Note

      Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).

  11. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

    Click here

  12. INSTALL GENERATOR ASSEMBLY

    Click here

  13. INSTALL V-RIBBED BELT

    Click here

  14. INSTALL NO. 2 VENTILATION HOSE


    1. Install the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

  15. INSTALL VENTILATION HOSE


    1. Install the ventilation hose to the PCV valve (ventilation valve sub-assembly) and slide the clip to secure it.

  16. INSTALL NO. 2 WATER BY-PASS HOSE


    1. Install the No. 2 water by-pass hose to the water outlet and slide the clip to secure it.

  17. INSTALL NO. 3 WATER BY-PASS HOSE


    1. Install the No. 3 water by-pass hose to the water inlet pipe and slide the clip to secure it.

  18. INSTALL VACUUM PUMP ASSEMBLY

    Click here

  19. INSTALL IGNITION COIL ASSEMBLY

    Click here

  20. INSTALL SENSOR WIRE


    1. Engage the 2 clamps and install the sensor wire to the water inlet pipe with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  21. INSTALL KNOCK CONTROL SENSOR

    Click here