ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | COOL AIR INTAKE DUCT SEAL | *2 | FRONT FENDER APRON SEAL LH |
| *3 | FRONT FENDER APRON SEAL RH | *4 | FRONT FENDER LINER LH |
| *5 | FRONT FENDER LINER RH | *6 | FRONT FLOOR COVER LH |
| *7 | NO. 1 ENGINE UNDER COVER | *8 | NO. 2 ENGINE UNDER COVER |
| *9 | RADIATOR SIDE DEFLECTOR SEAL LH | *10 | RADIATOR SIDE SEAL RH |
ILLUSTRATION
| *1 | OUTER COWL TOP PANEL SUB-ASSEMBLY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | BATTERY |
| *5 | BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY | *6 | INLET AIR CLEANER ASSEMBLY |
| *7 | RESERVOIR BRACKET | *8 | V-BANK COVER SUB-ASSEMBLY |
| *9 | BATTERY TRAY | *10 | BATTERY CLAMP |
| *11 | BATTERY CLAMP BOLT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COMPRESSOR ASSEMBLY WITH PULLEY | *2 | DISCHARGE HOSE SUB-ASSEMBLY |
| *3 | ENGINE MOVING CONTROL ROD | *4 | FUEL TUBE SUB-ASSEMBLY |
| *5 | INLET HEATER WATER HOSE | *6 | NO. 1 INLET OIL COOLER HOSE |
| *7 | NO. 1 FUEL VAPOR FEED HOSE | *8 | NO. 1 RADIATOR HOSE |
| *9 | NO. 2 ENGINE MOUNTING STAY RH | *10 | NO. 2 RADIATOR HOSE |
| *11 | NO. 3 ENGINE MOUNTING STAY RH | *12 | OUTLET HEATER WATER HOSE |
| *13 | NO. 1 OUTLET OIL COOLER HOSE | *14 | SUCTION HOSE SUB-ASSEMBLY |
| *15 | TRANSMISSION CONTROL CABLE ASSEMBLY | *16 | UNION TO CHECK VALVE HOSE |
| *17 | V-RIBBED BELT | *18 | ENGINE MOVING CONTROL ROD BRACKET |
| *19 | NO. 1 FUEL PIPE CLAMP | *20 | NO. 1 RELAY BLOCK COVER |
| *21 | ENGINE WIRE | *22 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY |
| *3 | NO. 1 EXHAUST PIPE SUPPORT BRACKET | *4 | COMPRESSION SPRING |
| *5 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for AWD | - | - |
| *1 | FRONT NO. 1 STABILIZER BRACKET LH | *2 | FRONT NO. 1 STABILIZER BRACKET RH |
| *3 | FRONT STABILIZER BAR | *4 | STEERING LINK ASSEMBLY |
| *5 | FRONT FRAME ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY WITH TRANSAXLE | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | ENGINE MOUNTING INSULATOR RH | *4 | ENGINE WIRE |
| *5 | FRONT ENGINE MOUNTING INSULATOR ASSEMBLY | *6 | FRONT FRAME ASSEMBLY |
| *7 | REAR ENGINE MOUNTING INSULATOR ASSEMBLY | *8 | STARTER ASSEMBLY |
| *9 | STEERING INTERMEDIATE SHAFT ASSEMBLY | *10 | FRAME SIDE PLATE LH |
| *11 | FRAME SIDE PLATE RH | *12 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *13 | FRONT SUSPENSION MEMBER REAR BRACE RH | *14 | HOLE PLUG |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for AWD | - | - |
| *1 | AUTOMATIC TRANSAXLE ASSEMBLY | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | *4 | FLYWHEEL HOUSING UNDER COVER |
| *5 | MANIFOLD STAY | *6 | NO. 1 EXHAUST PIPE SUPPORT BRACKET |
| *7 | RADIATOR PIPE CLAMP | *8 | TRANSFER STIFFENER PLATE RH |
| *9 | FRONT DRIVE PLATE SPACER | *10 | REAR DRIVE PLATE SPACER |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Adhesive 1324 |
| ★ | Precoated part | - | - |