CAMSHAFT COMPONENTS
ILLUSTRATION
| *1 | ENGINE MOUNTING BRACKET RH | *2 | GENERATOR ASSEMBLY |
| *3 | NO. 1 VACUUM SWITCHING VALVE | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst) | *2 | EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst) |
| *3 | IGNITION COIL ASSEMBLY | *4 | NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
| *5 | NO. 2 IDLER PULLEY SUB-ASSEMBLY | *6 | NO. 2 MANIFOLD STAY |
| *7 | V-RIBBED BELT TENSIONER ASSEMBLY | *8 | WATER PUMP PULLEY |
| *9 | NO. 2 IDLER PULLEY COVER PLATE | *10 | IDLER PULLEY COVER PLATE |
| *11 | EXHAUST MANIFOLD TO HEAD GASKET | *12 | EXHAUST MANIFOLD TO HEAD GASKET LH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | NO. 1 FRONT ENGINE MOUNTING BRACKET LH |
| *3 | NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE | *4 | NO. 2 TIMING GEAR COVER |
| *5 | ENGINE OIL LEVEL DIPSTICK | *6 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT POSITION SENSOR | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *3 | CYLINDER HEAD COVER SUB-ASSEMBLY LH | *4 | NO. 1 OIL PIPE |
| *5 | OIL PIPE | *6 | WATER INLET HOUSING |
| *7 | NO. 2 CYLINDER HEAD COVER GASKET | *8 | CYLINDER HEAD COVER GASKET |
| *9 | OIL CONTROL VALVE FILTER RH | *10 | OIL CONTROL VALVE FILTER LH |
| *11 | SEAL WASHER | *12 | GASKET |
| *13 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | NO. 1 OIL COOLER BRACKET | *2 | OIL COOLER ASSEMBLY |
| *3 | NO. 5 WATER BY-PASS HOSE | *4 | NO. 4 WATER BY-PASS HOSE |
| *5 | OIL COOLER PIPE | *6 | OIL COOLER UNION BOLT |
| *7 | O-RING | *8 | GASKET |
| *9 | HOSE CLAMP | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 2 OIL PAN SUB-ASSEMBLY | *2 | OIL PAN SUB-ASSEMBLY |
| *3 | OIL STRAINER SUB-ASSEMBLY | *4 | GASKET |
| *5 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT PULLEY | *4 | IDLE SPROCKET ASSEMBLY |
| *5 | NO. 1 CHAIN TENSIONER ASSEMBLY | *6 | TIMING CHAIN CASE OIL SEAL |
| *7 | TIMING CHAIN COVER SUB-ASSEMBLY | *8 | NO. 1 IDLE GEAR SHAFT |
| *9 | NO. 2 IDLE GEAR SHAFT | *10 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP Grease |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | for Bank 1 | - | - |
| *1 | CAMSHAFT | *2 | CAMSHAFT BEARING CAP |
| *3 | CAMSHAFT HOUSING SUB-ASSEMBLY RH | *4 | NO. 2 CAMSHAFT |
| *5 | NO. 2 CHAIN TENSIONER ASSEMBLY | *6 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *7 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY | *8 | NO. 2 CHAIN SUB-ASSEMBLY |
| *9 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 10 (102, 7) 2nd: 16 (163, 12) |
- | - |
ILLUSTRATION
| *A | for Bank 2 | - | - |
| *1 | CAMSHAFT BEARING CAP | *2 | CAMSHAFT HOUSING SUB-ASSEMBLY LH |
| *3 | NO. 3 CAMSHAFT | *4 | NO. 3 CHAIN TENSIONER ASSEMBLY |
| *5 | NO. 4 CAMSHAFT | *6 | NO. 2 CHAIN SUB-ASSEMBLY |
| *7 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY | *8 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *9 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 10 (102, 7) 2nd: 16 (163, 12) |
- | - |