ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | COOL AIR INTAKE DUCT SEAL | *2 | FRONT FENDER APRON SEAL LH |
| *3 | FRONT FENDER APRON SEAL RH | *4 | NO. 1 ENGINE UNDER COVER |
| *5 | FLOOR UNDER COVER LH | *6 | FRONT FENDER LINER LH |
| *7 | FRONT FENDER LINER RH | *8 | NO. 2 ENGINE UNDER COVER |
| *9 | RADIATOR SIDE SEAL RH | *10 | RADIATOR SIDE DEFLECTOR SEAL LH |
ILLUSTRATION
| *1 | BRAKE BOOSTER VACUUM EJECTOR | *2 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | BATTERY |
| *5 | NO. 1 ENGINE COVER SUB-ASSEMBLY | *6 | BATTERY CLAMP |
| *7 | INLET AIR CLEANER ASSEMBLY | *8 | BATTERY TRAY |
| *9 | NO. 1 AIR CLEANER BRACKET | *10 | BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
| *11 | RESERVOIR BRACKET | *12 | NO. 1 RELAY BLOCK COVER |
| *13 | ENGINE WIRE | *14 | BATTERY CLAMP BOLT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE WIRE | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | NO. 1 OUTLET OIL COOLER HOSE | *4 | NO. 1 RADIATOR HOSE |
| *5 | NO. 2 RADIATOR HOSE | *6 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *7 | UNION TO VACUUM TUBE HOSE | *8 | NO. 4 WATER BY-PASS HOSE |
| *9 | NO. 3 WATER BY-PASS HOSE | *10 | OUTLET HEATER WATER HOSE A |
| *11 | OUTLET HEATER WATER HOSE B | *12 | NO. 1 FUEL PIPE CLAMP |
| *13 | FUEL MAIN TUBE | *14 | NO. 1 INLET OIL COOLER HOSE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | COMPRESSOR ASSEMBLY WITH PULLEY | *2 | ENGINE MOVING CONTROL ROD |
| *3 | GENERATOR ASSEMBLY | *4 | DISCHARGE HOSE SUB-ASSEMBLY |
| *5 | SUCTION HOSE SUB-ASSEMBLY | *6 | NO. 2 ENGINE MOUNTING STAY RH |
| *7 | V-RIBBED BELT | *8 | O-RING |
| *9 | ENGINE MOVING CONTROL ROD BRACKET | *10 | NO. 3 ENGINE MOUNTING STAY RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *1 | FRONT AXLE SHAFT NUT LH | *2 | FRONT EXHAUST PIPE ASSEMBLY |
| *3 | FRONT SPEED SENSOR LH | *4 | FRONT STABILIZER LINK ASSEMBLY LH |
| *5 | STEERING INTERMEDIATE SHAFT ASSEMBLY | *6 | TIE ROD ASSEMBLY LH |
| *7 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH | *8 | COMPRESSION SPRING |
| *9 | COTTER PIN | *10 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *1 | ENGINE MOUNTING BRACKET RH | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | ENGINE MOUNTING INSULATOR RH | *4 | ENGINE WIRE |
| *5 | FRONT FRAME ASSEMBLY | *6 | FRONT ENGINE MOUNTING INSULATOR |
| *7 | FRONT SUSPENSION MEMBER REAR BRACE RH | *8 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *9 | FRAME SIDE RAIL PLATE RH | *10 | FRAME SIDE RAIL PLATE LH |
| *11 | HOLE PLUG | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | AUTOMATIC TRANSAXLE ASSEMBLY | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | *4 | DRIVE SHAFT BEARING BRACKET |
| *5 | FLYWHEEL HOUSING UNDER COVER | *6 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *7 | FRONT DRIVE SHAFT ASSEMBLY RH | *8 | FRONT DRIVE SHAFT HOLE SNAP RING LH |
| *9 | STARTER ASSEMBLY | *10 | BEARING BRACKET HOLE SNAP RING |
| *11 | FRONT DRIVE PLATE SPACER | *12 | REAR DRIVE PLATE SPACER |
| *13 | STUD BOLT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
ATF WS |  |
Adhesive 1324 |
| |
Do not apply lubricants to the threaded parts | ★ | Precoated part |