SFI SYSTEM, Diagnostic DTC:P003612, P003614, P005612, P005614, P102A9E, P105A9E

DTC Code DTC Name
P003612 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery
P003614 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open
P005612 HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Battery
P005614 HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Ground or Open
P102A9E O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On
P105A9E O2 Sensor Heater Performance Bank 2 Sensor 2 Stuck On

DESCRIPTION

Refer to DTC P013613.

Click here

Tech Tips


  • When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  • The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A0029Z5E37
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003612 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery Heated oxygen sensor heater current reaches high limit (1 trip detection logic).

  • Short in heated oxygen sensor (bank 1 sensor 2) heater circuit

  • Heated oxygen sensor (bank 1 sensor 2)

  • ECM

 Comes on DTC stored SAE Code: P0038
P003614 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).

  • Open or short in heated oxygen sensor (bank 1 sensor 2) heater circuit

  • Heated oxygen sensor (bank 1 sensor 2)

  • Semiconductor pwr integration ECU

  • ECM

 Comes on DTC stored SAE Code: P0037
P005612 HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Battery Heated oxygen sensor heater current reaches high limit (1 trip detection logic).

  • Short in heated oxygen sensor (bank 2 sensor 2) heater circuit

  • Heated oxygen sensor (bank 2 sensor 2)

  • ECM

 Comes on DTC stored SAE Code: P0058
P005614 HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Ground or Open Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).

  • Open or short in heated oxygen sensor (bank 2 sensor 2) heater circuit

  • Heated oxygen sensor (bank 2 sensor 2)

  • Semiconductor pwr integration ECU

  • ECM

 Comes on DTC stored SAE Code: P0057
P102A9E O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).

  • Short in heated oxygen sensor (bank 1 sensor 2) heater circuit

  • Heated oxygen sensor (bank 1 sensor 2)

  • ECM

 Comes on DTC stored SAE Code: P102D
P105A9E O2 Sensor Heater Performance Bank 2 Sensor 2 Stuck On Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).

  • Short in heated oxygen sensor (bank 2 sensor 2) heater circuit

  • Heated oxygen sensor (bank 2 sensor 2)

  • ECM

 Comes on DTC stored SAE Code: P105D

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.


MONITOR STRATEGY

Required Sensors/Components Heated oxygen sensor (sensor 2) heater
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Time after heater on 10 seconds or more

CONFIRMATION DRIVING PATTERN

A002AZ1E38

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on [A].

  6. Start the engine and idle it for 5 minutes or more [B].

  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

  8. Idle the engine for 5 minutes or more [D].

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P003612, P003614, P005612, P005614, P102A9E or P105A9E.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

WIRING DIAGRAM

Refer to DTC P013613.

Click here

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • Sensor 1 refers to the sensor closest to the engine assembly.

  • Sensor 2 refers to the sensor farthest away from the engine assembly.

  • Refer to "Data List / Active Test" [O2 Sensor Heater B1S2, O2 Sensor Heater Current Value B1S2, O2 Sensor Heater B2S2 and O2 Sensor Heater Current Value B2S2].

    Click here

  • When the values for the Data List item O2 Sensor Heater Current Value B1S2 and O2 Sensor Heater Current Value B2S2 are not 0 A, the heater is on.

  • Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage Click here. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)


    1. Inspect the heated oxygen sensor.


      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HEATED OXYGEN SENSOR for Bank 1: Click here for Bank 2: Click here

    OK

  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

    A002ALGC02
    *a

    Front view of wire harness connector

    (to Heated Oxygen Sensor)

    		 *b Bank 1
    *c Bank 2 - -

    1. Disconnect the heated oxygen sensor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      P1-1 (+B) - Body ground Ignition switch ON 11 to 14 V
      C51-2 (+B) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - HEATED OXYGEN SENSOR) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)


    1. Disconnect the heated oxygen sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P1-2 (HT1B) - C1-50 (HT1B) Always Below 1 Ω
      C51-1 (HT2B) - C1-16 (HT2B) Always Below 1 Ω
      P1-2 (HT1B) or C1-50 (HT1B) - Body ground and other terminals Always 10 kΩ or higher
      C51-1 (HT2B) or C1-16 (HT2B) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614, P005612, P005614, P102A9E OR P105A9E)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine / Trouble Codes.

    10. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P003612, P003614, P005612, P005614, P102A9E or P105A9E is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here

  5. CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - HEATED OXYGEN SENSOR)


    1. Disconnect the semiconductor pwr integration ECU connector.

    2. Disconnect the heated oxygen sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1G-7 - P1-1 (+B) Always Below 1 Ω
      1G-7 - C51-2 (+B) Always Below 1 Ω
      1G-7 or P1-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
      1G-7 or C51-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SEMICONDUCTOR PWR INTEGRATION ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR