FUEL INJECTOR(for Direct Injection) REMOVAL

PROCEDURE


  1. REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

    Click here

  2. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY


    1. A002AL4

      Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 2 fuel pipe sub-assembly.

    2. Remove the No. 2 fuel pipe sub-assembly from the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH.

  3. REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH


    1. A0028SV

      Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.

    2. A00278I

      Disengage the 2 clamps to disconnect the No. 6 engine wire connector and No. 7 engine wire connector.

    3. A00292V

      Disconnect the fuel pressure sensor connector.

    4. A0029HT

      Remove the bolt.

    5. Disengage the clamp to disconnect the No. 7 engine wire from the fuel delivery pipe with sensor assembly LH.

    6. A0029LBC01
      B003ZIE Bolt
      B003Z8F Nut

      Remove the 2 bolts, 2 nuts and fuel delivery pipe with sensor assembly LH with the fuel injector assemblies.

      Note


      • Make sure not to touch or strike the tips of the fuel injector assemblies.

      • Pull and remove the fuel delivery pipe with sensor assembly LH in a straight line without tilting it.

    7. A002CBB

      Disconnect the 3 fuel injector assembly connectors.

  4. REMOVE FUEL DELIVERY PIPE RH


    1. A0029IL

      Remove the bolt.

    2. Disengage the clamp to disconnect the No. 6 engine wire from the fuel delivery pipe RH.

    3. A0027AXC01
      B003ZIE Bolt
      B003Z8F Nut

      Remove the 2 bolts, 2 nuts and fuel delivery pipe RH with the fuel injector assemblies.

      Note


      • Make sure not to touch or strike the tips of the fuel injector assemblies.

      • Pull and remove the fuel delivery pipe RH in a straight line without tilting it.

    4. A002BJP

      Disconnect the 3 fuel injector assembly connectors.

  5. REMOVE FUEL INJECTOR ASSEMBLY


    1. A0027V5N01
      *1 No. 2

      Secure the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH in a vise between aluminum plates and pull out the 6 fuel injector assemblies.

      Note


      • Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH O-ring.

      • After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH side.

      • Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

    2. Remove the nozzle holder clamp from each fuel injector assembly.

    3. Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each fuel injector assembly.

      Note

      Do not damage the area that contacts the O-ring.

    4. Remove the O-ring and No. 1 fuel injector back-up ring from each fuel injector assembly.

    5. Remove the C-ring and injector vibration insulator from each fuel injector assembly.

  6. REMOVE FUEL INJECTOR SEAL


    1. A002BBD

      Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

      Note


      • Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.

      • If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.

    2. Remove the fuel injector seal from each fuel injector assembly.