AXLE AND DIFFERENTIAL SERVICE DATA

Axle
Front axle hub bearing looseness Maximum looseness: 0 mm (0 in.)
Front axle hub runout Maximum runout: 0.05 mm (0.00196 in.)
Rear axle hub bearing looseness Maximum looseness: 0 mm (0 in.)
Rear axle hub runout Maximum runout: 0.08 mm (0.00314 in.)
Rear Differential Carrier Assembly
Diaphragm oil seal drive in depth 0.7 to 1.3 mm (0.0276 to 0.0511 in.)
Rear drive shaft oil seal drive in depth 8.2 to 8.8 mm (0.323 to 0.346 in.)
Differential ring gear backlash 0.13 to 0.25 mm (0.00512 to 0.00984 in.)
Electro magnetic control coupling sub-assembly run out Vertical 0.06 mm (0.00236 in.)
Lateral 0.07 mm (0.00276 in.)
Differential drive pinion preload (at starting)

New bearing: 1.83 to 3.04 N*m (19 to 30 kgf*cm, 17 to 26 in.*lbf)

Reused bearing: 1.51 to 2.52 N*m (16 to 25 kgf*cm, 14 to 22 in.*lbf)
Total preload (at starting)

New bearing: 3.12 to 5.86 N*m (32 to 59 kgf*cm, 28 to 51 in.*lbf)

Reused bearing: 2.80 to 5.34 N*m (29 to 54 kgf*cm, 25 to 47 in.*lbf)
Rear differential side gear shaft plate washer thickness 75 1.74 to 1.76 mm (0.0686 to 0.0692 in.)
76 1.77 to 1.79 mm (0.0697 to 0.0704 in.)
77 1.80 to 1.82 mm (0.0709 to 0.0716 in.)
78 1.83 to 1.85 mm (0.0721 to 0.0728 in.)
79 1.86 to 1.88 mm (0.0733 to 0.0740 in.)
80 1.89 to 1.91 mm (0.0745 to 0.0751 in.)
81 1.92 to 1.94 mm (0.0756 to 0.0763 in.)
82 1.95 to 1.97 mm (0.0768 to 0.0775 in.)
83 1.98 to 2.00 mm (0.0780 to 0.0787 in.)
84 2.01 to 2.03 mm (0.0792 to 0.0799 in.)
85 2.04 to 2.06 mm (0.0804 to 0.0811 in.)
86 2.07 to 2.09 mm (0.0815 to 0.0822 in.)
88 2.10 to 2.12 mm (0.0827 to 0.0834 in.)
89 2.13 to 2.15 mm (0.0839 to 0.0846 in.)
90 2.16 to 2.18 mm (0.0851 to 0.0858 in.)
91 2.19 to 2.21 mm (0.0863 to 0.0870 in.)
92 2.22 to 2.24 mm (0.0875 to 0.0881 in.)
93 2.25 to 2.27 mm (0.0886 to 0.0893 in.)
94 2.28 to 2.30 mm (0.0898 to 0.0905 in.)
95 2.31 to 2.33 mm (0.0910 to 0.0917 in.)
96 2.34 to 2.36 mm (0.0922 to 0.0929 in.)
97 2.37 to 2.39 mm (0.0934 to 0.0940 in.)
98 2.40 to 2.42 mm (0.0945 to 0.0952 in.)
99 2.43 to 2.45 mm (0.0957 to 0.0964 in.)
00 2.46 to 2.48 mm (0.0969 to 0.0976 in.)
01 2.49 to 2.51 mm (0.0981 to 0.0988 in.)
02 2.52 to 2.54 mm (0.0993 to 0.0999 in.)
03 2.55 to 2.57 mm (0.1004 to 0.1011 in.)
04 2.58 to 2.60 mm (0.1016 to 0.1023 in.)
05 2.61 to 2.63 mm (0.1028 to 0.1035 in.)
06 2.64 to 2.66 mm (0.1040 to 0.1047 in.)
07 2.67 to 2.69 mm (0.1052 to 0.1059 in.)
08 2.70 to 2.72 mm (0.1063 to 0.1070 in.)
09 2.73 to 2.75 mm (0.1075 to 0.1082 in.)
10 2.76 to 2.78 mm (0.1087 to 0.1094 in.)
11 2.79 to 2.81 mm (0.1099 to 0.1106 in.)
12 2.82 to 2.84 mm (0.1111 to 0.1118 in.)
13 2.85 to 2.87 mm (0.1123 to 0.1129 in.)
14 2.88 to 2.90 mm (0.1134 to 0.1141 in.)
Rear differential drive pinion plate washer thickness 41 1.695 to 1.705 mm (0.0667 to 0.0671 in.)
43 1.715 to 1.725 mm (0.0675 to 0.0679 in.)
45 1.735 to 1.745 mm (0.0683 to 0.0687 in.)
47 1.755 to 1.765 mm (0.0690 to 0.0695 in.)
49 1.775 to 1.785 mm (0.0699 to 0.0703 in.)
51 1.795 to 1.805 mm (0.0707 to 0.0711 in.)
53 1.815 to 1.825 mm (0.0715 to 0.0719 in.)
55 1.835 to 1.845 mm (0.0722 to 0.0726 in.)
57 1.855 to 1.865 mm (0.0730 to 0.0734 in.)
59 1.875 to 1.885 mm (0.0738 to 0.0742 in.)
61 1.895 to 1.905 mm (0.0746 to 0.0750 in.)
63 1.915 to 1.925 mm (0.0754 to 0.0758 in.)
65 1.935 to 1.945 mm (0.0762 to 0.0766 in.)
71 1.955 to 1.965 mm (0.0770 to 0.0774 in.)
73 1.975 to 1.985 mm (0.0778 to 0.0781 in.)
75 1.995 to 2.005 mm (0.0785 to 0.0789 in.)
77 2.015 to 2.025 mm (0.0793 to 0.0797 in.)
79 2.035 to 2.045 mm (0.0801 to 0.0805 in.)
81 2.055 to 2.065 mm (0.0809 to 0.0813 in.)
83 2.075 to 2.085 mm (0.0817 to 0.0821 in.)
85 2.095 to 2.105 mm (0.0825 to 0.0829 in.)
87 2.115 to 2.125 mm (0.0833 to 0.0837 in.)
89 2.135 to 2.145 mm (0.0841 to 0.0844 in.)
91 2.155 to 2.165 mm (0.0848 to 0.0852 in.)
93 2.175 to 2.185 mm (0.0856 to 0.0860 in.)
95 2.195 to 2.205 mm (0.0864 to 0.0868 in.)
97 2.215 to 2.225 mm (0.0873 to 0.0875 in.)
99 2.235 to 2.245 mm (0.0880 to 0.0883 in.)