2GR-FKS ENGINE CONTROL SERVICE DATA

SPARK PLUG
Standard Insulation Resistance Spark plug (terminal part) - Body ground 10 MΩ or higher
Spark Plug Type DENSO made FK20HBR8
Maximum Electrode Gap for Used Spark Plug 1.1 mm (0.0433 in.)
Standard Electrode Gap for New Spark Plug 0.7 to 0.8 mm (0.0276 to 0.0315 in.)
CAMSHAFT TIMING GEAR BOLT
Standard Stroke for Intake Side 4.5 mm (0.177 in.) or more
for Exhaust Side 2.2 mm (0.0866 in.) or more
CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY
Plunger Extends Outwards 5.9 mm (0.232 in.) or more
THROTTLE BODY WITH MOTOR ASSEMBLY
Standard Resistance 1 (M-) - 2 (M+) 20°C (68°F) 0.3 to 100 Ω
ACCELERATOR PEDAL SENSOR ASSEMBLY
Standard Voltage Accelerator Position Sensor No. 1 Voltage Accelerator pedal fully released 0.5 to 1.1 V
Accelerator pedal fully depressed 2.6 to 4.5 V
Accelerator Position Sensor No. 2 Voltage Accelerator pedal fully released 1.2 to 2.0 V
Accelerator pedal fully depressed 3.4 to 4.75 V
MASS AIR FLOW METER SUB-ASSEMBLY
Standard Resistance 4 (THA) - 2 (E2G) -20°C (-4°F) 13.6 to 18.4 kΩ
20°C (68°F) 2.21 to 2.69 kΩ
60°C (140°F) 0.49 to 0.67 kΩ
ENGINE COOLANT TEMPERATURE SENSOR
Standard Resistance 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.310 to 0.326 kΩ
KNOCK CONTROL SENSOR
Standard Resistance 25°C (77°F) 120 to 280 kΩ
AIR FUEL RATIO SENSOR (for Bank 1)
Standard Resistance 1 (HA1A) - 2 (+B) 20°C (68°F) 1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher
AIR FUEL RATIO SENSOR (for Bank 2)
Standard Resistance 1 (HA2A) - 2 (+B) 20°C (68°F) 1.6 to 3.2 Ω
1 (HA2A) - 4 (A2A-) Always 10 kΩ or higher
HEATED OXYGEN SENSOR (for Bank 1)
Standard Resistance 2 (HT1B) - 1 (+B) 20°C (68°F) 5 to 10 Ω
2 (HT1B) - 3 (E2) Always 10 kΩ or higher
HEATED OXYGEN SENSOR (for Bank 2)
Standard Resistance 1 (HT2B) - 2 (+B) 20°C (68°F) 5 to 10 Ω
1 (HT2B) - 4 (E2) Always 10 kΩ or higher
INJECTOR RELAY (D INJ)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω
FUEL PUMP RELAY ASSEMBLY (FUEL PMP)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω