AUTOMATIC HIGH BEAM SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto High Beam Main Switch Auto high beam switch signal ON or OFF

      ON: Auto high beam switch pressed

      OFF: Auto high beam switch not pressed

      		 -
      Dimmer SW Dimmer switch high position signal ON or OFF

      ON: Dimmer switch in high or high flash position

      OFF: Dimmer switch in low position

      		 -
      Auto Light SW Light control switch AUTO position signal ON or OFF

      ON: Light control switch in AUTO position

      OFF: Light control switch not in AUTO position

      		 -
      Head Light SW (Head) Light control switch head position signal ON or OFF

      ON: Light control switch in head position

      OFF: Light control switch not in head position

      		 -
      Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx Value is output according to ambient light levels -
      Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS1 Automatic high beam sensor state past 1 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS2 Automatic high beam sensor state past 2 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS3 Automatic high beam sensor state past 3 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS4 Automatic high beam sensor state past 4 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS5 Automatic high beam sensor state past 5 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS6 Automatic high beam sensor state past 6 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      Auto H Beam STS7 Automatic high beam sensor state past 7 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed

      Undetec: undetected

      CAM NA: camera detection malfunction*1

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: system delay
      The Number of DTC Number of trouble codes 0 to 255 Condition can be displayed -

      • *1: If CAM NA is displayed, the lane departure warning camera may have stopped operating due to high temperature.