LIGHTING SYSTEM, Diagnostic DTC:B243D, B243E

DTC Code DTC Name
B243D Left Low Beam Fan Malfunction
B243E Right Low Beam Fan Malfunction

DESCRIPTION

A DTC is stored when a malfunction of the headlight fan occurs and the low beam headlight is dim. The No. 1 headlight ECU sub-assembly LH stores DTC B243D and B243E.

DTC No. Detection Item DTC Detection Condition Trouble Area
B243D Left Low Beam Fan Malfunction Malfunction of headlight fan occurs and low beam headlight LH is dim

  • Headlight unit assembly LH

  • Headlight unit LH

  • No. 1 headlight ECU sub-assembly LH
B243E Right Low Beam Fan Malfunction Malfunction of headlight fan occurs and low beam headlight RH is dim

  • Headlight unit assembly RH

  • Headlight unit RH

  • No. 1 headlight ECU sub-assembly RH

WIRING DIAGRAM


  1. for Bulb Type Turn Signal Light

    A002377E29

  2. for LED Type Turn Signal Light

    A002377E30

CAUTION / NOTICE / HINT

Note

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click here

PROCEDURE


  1. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

    5. Clear the DTCs.


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Operate the light control switch to turn on the low beam headlights and wait 2 minutes.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

    6. Check for DTCs.


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B243D and B243E are not output.
      Result
      Result Proceed to
      OK A
      NG (DTC B243D is output) B
      NG (DTC B243E is output) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    INSPECT HEADLIGHT UNIT RH Click here

    B

  3. INSPECT HEADLIGHT UNIT LH


    1. Remove the headlight unit LH.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

    2. Remove the headlight unit assembly LH.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

    3. Inspect the headlight unit LH.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HEADLIGHT UNIT LH for Bulb Type Turn Signal Light: Click here
    REPLACE HEADLIGHT UNIT LH for LED Type Turn Signal Light: Click here

    OK

  4. REPLACE HEADLIGHT UNIT ASSEMBLY LH


    1. Replace the headlight unit assembly LH with a new or known good one.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

    5. Clear the DTCs.


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Operate the light control switch to turn on the low beam headlights and wait 2 minutes.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

    6. Check for DTCs.


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B243D is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH Click here

  7. INSPECT HEADLIGHT UNIT RH


    1. Remove the headlight unit RH.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

    2. Remove the headlight unit assembly RH.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

    3. Inspect the headlight unit RH.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HEADLIGHT UNIT RH for Bulb Type Turn Signal Light: Click here
    REPLACE HEADLIGHT UNIT RH for LED Type Turn Signal Light: Click here

    OK

  8. REPLACE HEADLIGHT UNIT ASSEMBLY RH


    1. Replace the headlight unit assembly RH with a new or known good one.

      for Bulb Type Turn Signal Light: Click here

      for LED Type Turn Signal Light: Click here

      Result
      Proceed to
      NEXT

    NEXT

  9. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

    5. Clear the DTCs.


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  10. CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Operate the light control switch to turn on the low beam headlights and wait 2 minutes.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

    6. Check for DTCs.


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B243E is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH Click here