POWER MIRROR CONTROL SYSTEM(w/o Memory) Mirror Heater does not Operate with Rear Defogger Switch

DESCRIPTION

When the mirror heater switch (rear window defogger switch) on the air conditioning control assembly is pressed, the operation signal is sent to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on a relay in the semiconductor power integration ECU to operate the mirror heaters.

WIRING DIAGRAM

A0021FSE14

CAUTION / NOTICE / HINT

Note


  • If the auxiliary battery voltage is low, the power mirror control system (w/o Memory) may not operate. When "Operation of Electrical Items Restricted." is not displayed on the multi-information display in the combination meter assembly, check the Data List item "Battery Control Count (Body ECU)".

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Air Conditioner > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Defogger Relay (Rear) Mirror Heater OFF or ON -

      Body Electrical > Air Conditioner > Active Test
      Tester Display
      Defogger Relay (Rear)
      Result
      Result Proceed to
      Mirror heater operation on both mirrors is not normal A
      Mirror heater operation on RH side mirror is not normal B
      Mirror heater operation on LH side mirror is not normal C

    B

    CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY - OUTER MIRROR ACTUATOR ASSEMBLY RH - BODY GROUND) Click here

    C

    CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY - OUTER MIRROR ACTUATOR ASSEMBLY LH - BODY GROUND) Click here

    A

  2. CHECK WINDOW DEFOGGER SYSTEM


    1. Check the window defogger system operation.

      Click here

      OK
      The window defogger system operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO WINDOW DEFOGGER SYSTEM Click here

    OK

  3. CHECK MIRROR HEATER RELAY


    1. Remove the mirror heater relay from the No. 1 engine room relay block and No. 1 junction block assembly.

    2. Inspect the mirror heater relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MIRROR HEATER RELAY

    OK

  4. CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY - SEMICONDUCTOR PWR INTEGRATION ECU)


    1. A0022EBC05
      *1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 1 - 1C-1(L) Always Below 1 Ω
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 1 - Body ground Always 10 kΩ or higher
      1C-1(L) - Body ground Always 10 kΩ or higher
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 2 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY POWER SOURCE)


    1. A0022EBC05
      *1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 1 - Body ground Power switch on (IG), rear defogger switch on 11 to 14 V
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 5 - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY - OUTER MIRROR ACTUATOR ASSEMBLY RH/LH - BODY GROUND)


    1. Disconnect the N8 outer mirror actuator assembly RH connector.

    2. Disconnect the N23 outer mirror actuator assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - N8-4(+) Always Below 1 Ω
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - N23-4(+) Always Below 1 Ω
      N8-4(+) - Body ground Always 10 kΩ or higher
      N23-4(+) - Body ground Always 10 kΩ or higher
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY - OUTER MIRROR ACTUATOR ASSEMBLY RH - BODY GROUND)


    1. A0022EBC05
      *1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

      Remove the mirror heater relay from the No. 1 engine room relay block and No. 1 junction block assembly.

    2. Disconnect the N8 outer mirror actuator assembly RH connector.

    3. Disconnect the N23 outer mirror actuator assembly LH connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - N8-4(+) Always Below 1 Ω
      N8-12 (-) - Body Ground Always Below 1 Ω
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - Body Ground Always 10 kΩ or higher
      N8-4 (+) - Body Ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT OUTER MIRROR RH (MIRROR HEATER)


    1. Remove the outer mirror RH.

      Click here

    2. Inspect the outer mirror RH.

      Click here

      OK
      Outer mirror RH is normal.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE OUTER MIRROR ACTUATOR ASSEMBLY RH Click here

    NG

    REPLACE OUTER MIRROR RH Click here

  9. CHECK HARNESS AND CONNECTOR (MIRROR HEATER RELAY - OUTER MIRROR ACTUATOR ASSEMBLY LH - BODY GROUND)


    1. A0022EBC05
      *1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

      Remove the mirror heater relay from the No. 1 engine room relay block and No. 1 junction block assembly.

    2. Disconnect the N23 outer mirror actuator assembly LH connector.

    3. Disconnect the N8 outer mirror actuator assembly RH connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - N23-4(+) Always Below 1 Ω
      N23-12 (-) - Body Ground Always Below 1 Ω
      No. 1 engine room relay block and No. 1 junction block assembly mirror heater relay terminal 3 - Body Ground Always 10 kΩ or higher
      N23-4 (+) - Body Ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT OUTER MIRROR LH (MIRROR HEATER)


    1. Remove the outer mirror LH.

      Click here

    2. Inspect the outer mirror LH.

      Click here

      OK
      Outer mirror LH is normal.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE OUTER MIRROR ACTUATOR ASSEMBLY LH Click here

    NG

    REPLACE OUTER MIRROR LH Click here