POWER MIRROR CONTROL SYSTEM(w/ Memory) AUTO Power Retract Mirrors do not operate

DESCRIPTION

The multiplex network master switch assembly sends the auto retractable outer mirror switch signal to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) sends the auto retract/return signal to the outer mirror control ECU assemblies via CAN communication, which then controls the mirrors.

When the outer mirror control ECU assemblies receive a door lock output signal from the main body ECU (multiplex network body ECU) while the auto retractable outer mirror switch is on, the outer mirror control ECU assemblies operate the retract motors built into the outer rear view mirror assemblies to retract or return the outer rear view mirror assemblies.

WIRING DIAGRAM

A002258E07

CAUTION / NOTICE / HINT

Note


  • The power mirror control system (w/ Memory) uses the CAN communication system and LIN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE


  1. CHECK POWER RETRACT MIRROR FUNCTION


    1. Check the power retract mirror function.

      Click here

      OK
      Power retract mirror function operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO OTHER DIAGNOSIS PROCEDURE (Power Retractable Mirrors do not Operate with Power Retract Mirror Switch) Click here

    OK

  2. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. Check the power door lock control system.

      Click here

      OK
      Power door lock control system is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  3. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Check the wireless door lock control system.

      Click here

      OK
      Wireless door lock control system is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO WIRELESS DOOR LOCK CONTROL SYSTEM Click here

    OK

  4. CHECK ENTRY AND START SYSTEM (for Entry Function)


    1. Check the entry and start system (for Entry Function).

      Click here

      OK
      Entry and Start System (for Entry Function) is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO ENTRY AND START SYSTEM (for Entry Function) Click here

    OK

  5. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Master Switch / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Master Switch > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto Mirror SW Auto retractable outer mirror switch signal OFF or ON

      OFF: Auto retractable outer mirror switch off

      ON: Auto retractable outer mirror switch on

      		 -

      Body Electrical > Master Switch > Data List
      Tester Display
      Auto Mirror SW
      OK
      On the GTS screen, ON or OFF is displayed for each item according to the table above.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

  6. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    1. Temporarily replace the multiplex network master switch assembly with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. CHECK AUTO POWER RETRACT MIRROR FUNCTION


    1. Check the auto power retract mirror function.

      Click here

      OK
      Auto power retract mirror function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here