POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

DESCRIPTION

The multiplex network master switch assembly sends the retractable outer mirror switch signal to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on the signal, each outer mirror control ECU assembly retracts or returns its corresponding outer rear view mirror assembly.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. READ VALUE USING GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Body Electrical / Master Switch / Data List.

   5. Read the Data List according to the display on the GTS.

      
      Body Electrical > Master Switch > Data List

      Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
      Outer Mirror Fold SW	Retractable outer mirror switch signal	OFF or ON	OFF: Retractable outer mirror switch off ON: Retractable outer mirror switch on	-

      
      Body Electrical > Master Switch > Data List

      Tester Display
      Outer Mirror Fold SW

      OK
      On the GTS screen, ON or OFF is displayed for each item according to the above.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

   OK

2. PERFORM ACTIVE TEST USING GTS

   
   

   1. Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.

   2. Perform the Active Test according to the display on the GTS.

      
      Body Electrical > Mirror L > Active Test

      Tester Display	Measurement Item	Control Range	Diagnostic Note
      Mirror Fold/Return	Mirror retract operation	OFF, Return or Fold	operate with the power switch on (IG) and the vehicle stopped. This test activates the Fold / Return. This operation can be confirmed by watching the mirror move in the desired direction.

      
      Body Electrical > Mirror L > Active Test

      Tester Display
      Mirror Fold/Return

      
      Body Electrical > Mirror R > Active Test

      Tester Display	Measurement Item	Control Range	Diagnostic Note
      Mirror Fold/Return	Mirror retract operation	OFF, Return or Fold	operate with the power switch on (IG) and the vehicle stopped. This test activates the Fold / Return. This operation can be confirmed by watching the mirror move in the desired direction.

      
      Body Electrical > Mirror R > Active Test

      Tester Display
      Mirror Fold/Return

      Result
      Result Proceed to Outer rear view mirror assemblies operate normally A Outer rear view mirror assembly (driver door) does not operate normally B Outer rear view mirror assembly (front passenger door) does not operate normally C

   
   

   A

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

   C

   INSPECT OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER DOOR) Click here

   B

3. INSPECT OUTER MIRROR ACTUATOR ASSEMBLY (DRIVER DOOR)

   
   

   1. Remove the outer mirror actuator assembly (driver door).

      Click here

   2. Inspect the outer mirror actuator assembly (driver door).

      Click here

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (DRIVER DOOR) Click here

   OK

4. REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

   
   

   1. Temporarily replace the outer mirror control ECU assembly (driver door) with a new or known good one.

      Click here

      Result
      Proceed to NEXT

   
   

   NEXT

5. CHECK POWER RETRACT MIRROR FUNCTION

   
   

   1. Check the power retract mirror function operates normally.

      Click here

      OK
      Power retract mirror function operates normally.

      Result
      Proceed to OK NG

   
   

   OK

   END (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

   NG

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

6. INSPECT OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER DOOR)

   
   

   1. Remove the outer mirror actuator assembly (front passenger door).

      Click here

   2. Inspect the outer mirror actuator assembly (front passenger door).

      Click here

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER DOOR) Click here

   OK

7. REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

   
   

   1. Temporarily replace the outer mirror control ECU assembly (front passenger door) with a new or known good one.

      Click here

      Result
      Proceed to NEXT

   
   

   NEXT

8. CHECK POWER RETRACT MIRROR FUNCTION

   
   

   1. Check the power retract mirror function operates normally.

      Click here

      OK
      Power retract mirror function operates normally.

      Result
      Proceed to OK NG

   
   

   OK

   END (OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

   NG

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

9. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

   
   

   1. Temporarily replace the multiplex network master switch assembly with a new or known good one.

      Click here

      Result
      Proceed to NEXT

   
   

   NEXT

10. CHECK POWER RETRACT MIRROR FUNCTION

    
    

    1. Check the power retract mirror function operates normally.

       Click here

       OK
       Power retract mirror function operates normally.

       Result
       Proceed to OK NG

    
    

    OK

    END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here