AIRBAG SYSTEM, Diagnostic DTC:B1627/82, B1628/82, B1637/82, B1638/82, B1647/82

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, rear seat airbag assembly LH*, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.

The side airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

• *: w/ Rear Seat Side Airbags

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK CURRENT DTC

   
   

   1. Check for current DTCs.

      Click here

      
      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      
      

      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

      • Codes other than current DTCs B1627, B1628, B1637, B1638, B1647 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to Current DTC B1647 or 82 is output. A Current DTC B1638 is output. B Current DTC B1627 or B1628 is output. C Current DTC B1637 is output. D Current DTCs B1627, B1628, B1637, B1638, B1647 and 82 are not output. E

   
   

   B

   CHECK HISTORY DTC Click here

   C

   CHECK CONNECTORS Click here

   D

   CHECK REAR AIRBAG SENSOR LH Click here

   E

   USE SIMULATION METHOD TO CHECK Click here

   A

2. CHECK CONNECTORS

   
   

   1. Turn the power switch off.

   2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

   3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

   4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.

   5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

3. CHECK NO. 2 FLOOR WIRE (OPEN)

   
   
   1. 

      *1	Rear Airbag Sensor LH
      *2	Airbag Sensor Assembly
      *3	No. 2 Floor Wire
      *4	Service Wire
      *a	Front view of wire harness connector (to Airbag Sensor Assembly)
      *b	Front view of wire harness connector (to Rear Airbag Sensor LH)

      Using a service wire, connect terminals 17 (BBL+) and 18 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Q22-4 (BCL+) - Q22-3 (BCL-) Always Below 1 Ω

   3. Disconnect the service wire from connector B.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

4. CHECK NO. 2 FLOOR WIRE (SHORT)

   
   
   1. 

      *1	Rear Airbag Sensor LH
      *2	Airbag Sensor Assembly
      *3	No. 2 Floor Wire
      *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Q22-4 (BCL+) - Q22-3 (BCL-) Always 1 MΩ or higher

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

5. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

   
   
   1. 

      *1	Rear Airbag Sensor LH
      *2	Airbag Sensor Assembly
      *3	No. 2 Floor Wire
      *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

   2. Turn the power switch on (IG).

   3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition Q22-4 (BCL+) - Body ground Power switch on (IG) Below 1 V Q22-3 (BCL-) - Body ground Power switch on (IG) Below 1 V

   4. Turn the power switch off.

   5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

6. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

   
   
   1. 

      *1	Rear Airbag Sensor LH
      *2	Airbag Sensor Assembly
      *3	No. 2 Floor Wire
      *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Q22-4 (BCL+) - Body ground Always 1 MΩ or higher Q22-3 (BCL-) - Body ground Always 1 MΩ or higher

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

7. CHECK NO. 2 FLOOR WIRE (OPEN)

   
   
   1. 

      *1	Side Airbag Sensor Assembly LH
      *2	Rear Airbag Sensor LH
      *3	No. 2 Floor Wire
      *4	Service Wire
      *a	Front view of wire harness connector (to Rear Airbag Sensor LH)
      *b	Front view of wire harness connector (to Side Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 2 (BBL+) and 1 (BBL-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Q22-1 (BBL+) - Q22-2 (BBL-) Always Below 1 Ω

   3. Disconnect the service wire from connector C.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

8. CHECK NO. 2 FLOOR WIRE (SHORT)

   
   
   1. 

      *1	Side Airbag Sensor Assembly LH
      *2	Rear Airbag Sensor LH
      *3	No. 2 Floor Wire
      *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Q22-1 (BBL+) - Q22-2 (BBL-) Always 1 MΩ or higher

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

9. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

   
   
   1. 

      *1	Side Airbag Sensor Assembly LH
      *2	Rear Airbag Sensor LH
      *3	No. 2 Floor Wire
      *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

   2. Turn the power switch on (IG).

   3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition Q22-1 (BBL+) - Body ground Power switch on (IG) Below 1 V Q22-2 (BBL-) - Body ground Power switch on (IG) Below 1 V

   4. Turn the power switch off.

   5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 FLOOR WIRE

   OK

10. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

    
    
    1. 

       *1	Side Airbag Sensor Assembly LH
       *2	Rear Airbag Sensor LH
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-1 (BBL+) - Body ground Always 1 MΩ or higher Q22-2 (BBL-) - Body ground Always 1 MΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

11. CHECK REAR AIRBAG SENSOR LH

    
    
    1. 

       *1	Rear Airbag Sensor RH
       *2	Airbag Sensor Assembly

       Connect the connectors to the side airbag sensor assembly LH and airbag sensor assembly.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1647 or 82 is output. A DTC B1642 or 81 is output. B DTCs B1642, B1647, 81 and 82 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

    
    

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

12. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

    
    
    1. 

       *1	Side Airbag Sensor Assembly RH
       *2	Rear Airbag Sensor LH

       Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1647 or 82 is output. A DTC B1642 or 81 is output. B DTCs B1642, B1647, 81 and 82 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

    
    

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

13. CHECK HISTORY DTC

    
    

    1. Check for history DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than history DTC B1637 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to History DTC B1637 is not output. A History DTC B1637 is output. B

    
    

    B

    CHECK REAR AIRBAG SENSOR LH Click here

    A

14. CHECK CONNECTORS

    
    

    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor LH.

       OK
       The connectors are properly connected.

       Tech Tips

       If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and rear airbag sensor LH.

    5. Check that the terminals of the connectors are not damaged.

       OK
       The terminals are not deformed or damaged.

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

15. CHECK NO. 2 FLOOR WIRE (OPEN)

    
    
    1. 

       *1	Rear Airbag Sensor LH
       *2	Airbag Sensor Assembly
       *3	No. 2 Floor Wire
       *4	Service Wire
       *a	Front view of wire harness connector (to Airbag Sensor Assembly)
       *b	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Using a service wire, connect terminals 17 (BBL+) and 18 (BBL-) of connector B.

       Note

       Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-4 (BCL+) - Q22-3 (BCL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

16. CHECK NO. 2 FLOOR WIRE (SHORT)

    
    
    1. 

       *1	Rear Airbag Sensor LH
       *2	Airbag Sensor Assembly
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-4 (BCL+) - Q22-3 (BCL-) Always 1 MΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

17. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

    
    
    1. 

       *1	Rear Airbag Sensor LH
       *2	Airbag Sensor Assembly
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

       Standard Voltage
       Tester Connection Condition Specified Condition Q22-4 (BCL+) - Body ground Power switch on (IG) Below 1 V Q22-3 (BCL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

18. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

    
    
    1. 

       *1	Rear Airbag Sensor LH
       *2	Airbag Sensor Assembly
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-4 (BCL+) - Body ground Always 1 MΩ or higher Q22-3 (BCL-) - Body ground Always 1 MΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

19. CHECK REAR AIRBAG SENSOR LH

    
    
    1. 

       *1	Rear Airbag Sensor RH
       *2	Airbag Sensor Assembly

       Connect the connector to the airbag sensor assembly.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1638 is output. A DTC B1633 is output. B DTCs B1633 and B1638 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

    
    

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

20. CHECK REAR AIRBAG SENSOR LH

    
    
    1. 

       *1	Rear Airbag Sensor RH
       *2	Airbag Sensor Assembly

       Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the rear airbag sensor LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1637 is output. A DTC B1632 is output. B DTCs B1632 and B1637 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

    
    

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

21. CHECK CONNECTORS

    
    

    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor assembly LH and rear airbag sensor LH.

       OK
       The connectors are properly connected.

       Tech Tips

       If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.

    5. Check that the terminals of the connectors are not damaged.

       OK
       The terminals are not deformed or damaged.

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

22. CHECK NO. 2 FLOOR WIRE (OPEN)

    
    
    1. 

       *1	Side Airbag Sensor Assembly LH
       *2	Rear Airbag Sensor LH
       *3	No. 2 Floor Wire
       *4	Service Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)
       *b	Front view of wire harness connector (to Side Airbag Sensor Assembly LH)

       Using a service wire, connect terminals 2 (BBL+) and 1 (BBL-) of connector C.

       Note

       Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-1 (BBL+) - Q22-2 (BBL-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

23. CHECK NO. 2 FLOOR WIRE (SHORT)

    
    
    1. 

       *1	Side Airbag Sensor Assembly LH
       *2	Rear Airbag Sensor LH
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-1 (BBL+) - Q22-2 (BBL-) Always 1 MΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

24. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

    
    
    1. 

       *1	Side Airbag Sensor Assembly LH
       *2	Rear Airbag Sensor LH
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

       Standard Voltage
       Tester Connection Condition Specified Condition Q22-1 (BBL+) - Body ground Power switch on (IG) Below 1 V Q22-2 (BBL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

25. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

    
    
    1. 

       *1	Side Airbag Sensor Assembly LH
       *2	Rear Airbag Sensor LH
       *3	No. 2 Floor Wire
       *a	Front view of wire harness connector (to Rear Airbag Sensor LH)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition Q22-1 (BBL+) - Body ground Always 1 MΩ or higher Q22-2 (BBL-) - Body ground Always 1 MΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

26. CHECK REAR AIRBAG SENSOR LH

    
    
    1. 

       *1	Rear Airbag Sensor RH
       *2	Airbag Sensor Assembly

       Connect the connector to the side airbag sensor assembly LH.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1622, B1623, B1627 and B1628 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1627 or B1628 is output. A DTC B1622 or B1623 is output. B DTCs B1622, B1623, B1627 and B1628 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

    
    

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

27. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

    
    
    1. 

       *1	Side Airbag Sensor Assembly RH
       *2	Rear Airbag Sensor LH

       Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1622, B1623, B1627 and B1628 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1627 or B1628 is output. A DTC B1622 or B1623 is output. B DTCs B1622, B1623, B1627 and B1628 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

    
    

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

28. CHECK REAR AIRBAG SENSOR LH

    
    
    1. 

       *1	Rear Airbag Sensor RH
       *2	Airbag Sensor Assembly

       Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

       CAUTION:

       Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the rear airbag sensor LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

       Click here

       
       Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

       Click here

       
       Body Electrical > SRS Airbag > Trouble Codes

       Tech Tips

       Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

       Result
       Result Proceed to DTC B1637 is output. A DTC B1632 is output. B DTCs B1632 and B1637 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

    
    

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here