METER / GAUGE SYSTEM, Diagnostic DTC:B150A

DTC Code DTC Name
B150A Lost Communication with HMI-LAN

DESCRIPTION

The combination meter assembly receives a text data signal from the radio receiver assembly via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150A Lost Communication with HMI-LAN After the combination meter assembly receives a registration information signal, which is sent by the radio receiver assembly when the power switch is on (ACC), 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.

  • Harness or connector

  • Radio receiver assembly

  • Combination meter assembly

 DTC stored

  • w/ Navigation System

  • w/ Audio and Visual System

WIRING DIAGRAM

Figure 1. w/ Navigation System

A0022V6E05
*a Radio Receiver Assembly
*b Combination Meter Assembly
*c Local Bus Communication Line

Figure 2. w/ Audio and Visual System

A0022V6E04
*a Radio Receiver Assembly
*b Combination Meter Assembly
*c Local Bus Communication Line

PROCEDURE


  1. CHECK FOR DTC


    1. w/ Navigation System


      1. Check if navigation system DTCs are output.

        Click here


        Body Electrical > Navigation System > Trouble Codes
        OK
        Navigation system DTCs are not output.

    2. w/ Audio and Visual System


      1. Check if audio and visual system DTCs are output.

        w/ Parallel Parking Assist Function: Click here

        w/o Parallel Parking Assist Function: Click here


        Body Electrical > Navigation System > Trouble Codes
        OK
        Audio and visual system DTCs are not output.
      Result
      Result Proceed to
      DTCs are not output A
      DTCs are output (w/ Navigation System ) B
      DTCs are output (w/ Audio and Visual System ) C

    B

    GO TO NAVIGATION SYSTEM Click here

    C

    GO TO AUDIO AND VISUAL SYSTEM w/ Parallel Parking Assist Function: Click here
    GO TO AUDIO AND VISUAL SYSTEM w/o Parallel Parking Assist Function: Click here

    A

  2. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Disconnect the K58 radio receiver assembly connector.*1

    2. Disconnect the K135 radio receiver assembly connector.*2

    3. Disconnect the K4 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K58-4 (CNL1) - K4-9 (MSCL)*1 Always Below 1 Ω
      K58-3 (CNH1) - K4-10 (MSCH)*1 Always Below 1 Ω
      K135-4 (CNL1) - K4-9 (MSCL)*2 Always Below 1 Ω
      K135-3 (CNH1) - K4-10 (MSCH)*2 Always Below 1 Ω
      K58-4 (CNL1) or K4-9 (MSCL) - Body ground*1 Always 10 kΩ or higher
      K58-3 (CNH1) or K4-10 (MSCH) - Body ground*1 Always 10 kΩ or higher
      K135-4 (CNL1) or K4-9 (MSCL) - Body ground*2 Always 10 kΩ or higher
      K135-3 (CNH1) or K4-10 (MSCH) - Body ground*2 Always 10 kΩ or higher

      • *1: w/ Navigation System

      • *2: w/ Audio and Visual System

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. REPLACE COMBINATION METER ASSEMBLY


    1. Replace the combination meter assembly with a new or known good one.

      Click here

    2. Turn the power switch on (IG) and wait 30 seconds.

      Note

      A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.

    3. A0021L1C03
      *a Multi-information Display
      *b Audio Tab

      Operate the steering pad switch assembly and check that the audio tab illuminates.

      Note

      For F SPORT models, operate the steering pad switch assembly after moving the movable meter ring.

    4. Check for DTCs.

      Click here


      Body Electrical > Combination Meter > Trouble Codes
      Result
      Result Proceed to
      The audio tab illuminates and DTC B150A is not output A
      The audio tab does not illuminate and DTC B150A is output B

    A

    END

    B

    REPLACE RADIO RECEIVER ASSEMBLY w/ Navigation Receiver: Click here
    REPLACE RADIO RECEIVER ASSEMBLY w/ Audio and Visual System: Click here