LIGHTING SYSTEM Rear Door Courtesy Switch Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the rear door courtesy light switch assembly.

WIRING DIAGRAM

A011ONKE02
*a Rear Door Courtesy Light Switch Assembly RH
*b Rear Door Courtesy Light Switch Assembly LH
*c Instrument Panel Junction Block Assembly
*d Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

Note

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RR Door Courtesy SW Rear door courtesy light switch assembly RH signal ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch assembly LH signal ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      RR Door Courtesy SW
      RL Door Courtesy SW
      OK
      Normal conditions listed above are displayed.
      Result
      Proceed to Proceed to
      OK A
      RR Door Courtesy SW is not normal B
      RL Door Courtesy SW is not normal C

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH Click here

    B

  2. INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH


    1. Remove the rear door courtesy light switch assembly RH.

      Click here

    2. Inspect the rear door courtesy light switch assembly RH.

      Click here

      OK
      Rear door courtesy light switch assembly RH is normal.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the 4B instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P7-1 - 4B-17 Always Below 1 Ω
      P7-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      Click here

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01MRV4C16
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      4B-17 - MB-2 (RCTY) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

  5. INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH


    1. Remove the rear door courtesy light switch assembly LH.

      Click here

    2. Inspect the rear door courtesy light switch assembly LH.

      Click here

      OK
      Rear door courtesy light switch assembly LH is normal.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the 4D instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q16-1 - 4D-25 Always Below 1 Ω
      Q16-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      Click here

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A011MHGC04
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      4D-25 - MB-13 (LCTY) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here