IMMOBILISER SYSTEM, Diagnostic DTC:B2784

DTC Code DTC Name
B2784 Antenna Coil Open / Short

DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short

The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)). (1 trip detection logic*)


  • Terminal AGND, VC5, TXCT or CODE circuit is open (includes disconnection of the power switch).

  • The transponder key amplifier coil built into the power switch is open.

  • Power switch

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

DTC output confirmation operation:


  • With the shift lever in P and the key held near the power switch, a hybrid control system start operation is performed by pressing and holding the power switch when the transmitter battery is depleted.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when transmitter battery is depleted by holding transmitter near power switch and pressing and holding power switch with shift lever in P -
Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

A0022TZE47
*1 CODE
*2 Power Switch
*3 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)


    1. Disconnect the K137 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the K50 power switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K137-15 (VC5) - K50-10 (VC5) Always Below 1 Ω
      K137-14 (TXCT) - K50-7 (TXCT) Always Below 1 Ω
      K137-13 (CODE) - K50-8 (CODE) Always Below 1 Ω
      K137-12 (AGND) - K50-6 (AGND) Always Below 1 Ω
      K137-15 (VC5) or K50-10 (VC5) - Body ground Always 10 kΩ or higher
      K137-14 (TXCT) or K50-7 (TXCT) - Body ground Always 10 kΩ or higher
      K137-13 (CODE) or K50-8 (CODE) - Body ground Always 10 kΩ or higher
      K137-12 (AGND) or K50-6 (AGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. REPLACE POWER SWITCH


    1. Temporarily replace the power switch with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  3. CLEAR DTC


    1. Clear the DTCs.


      Body Electrical > Entry&Start > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK FOR DTC


    1. Perform "DTC Output Confirmation Operation" procedure.

    2. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      OK
      DTC B2784 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (POWER SWITCH WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)