ENTRY AND START SYSTEM(for Entry Function) Room Oscillator does not Recognize Key

DESCRIPTION

If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly (front floor) or (rear floor)) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.

When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna and then sent to the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

A00222TE25
*a No. 2 Indoor Electrical Key Antenna Assembly (Front Floor)
*b Indoor Electrical Key Antenna (Rear Floor)
*c Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

    Click here

  • When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) Precaution.

    Click here

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

  • The indoor electrical key antenna assemblies have an antenna coil between each terminal.

  • The door control receiver is also related to interior verification.

PROCEDURE


  1. CHECK START OPERATION


    1. Using another registered electrical key transmitter sub-assembly, check that the hybrid control system starts.

      Result
      Result Proceed to
      Hybrid control system can be started A
      Hybrid control system cannot be started B

    A

    END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

    B

  2. CHECK ENTRY LOCK OPERATION


    1. Check that the entry lock and unlock functions operate on each door.

      Tech Tips

      If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.

      Result
      Result Proceed to
      All door entry functions operate normally A
      All door entry functions does not operate normally B

    B

    GO TO OTHER PROBLEM Click here

    A

  3. CHECK PUSH-BUTTON START FUNCTION


    1. A0021OFC01
      *1 Power Switch
      *2 Electrical Key Transmitter Sub-assembly

      Remove the transmitter battery of the electrical key transmitter sub-assembly.

      Click here

    2. With the brake pedal depressed, face the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the transmitter near the power switch and then press the power switch.

    3. When operating the power switch, check whether the hybrid control system starts.

      Tech Tips


      • When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the hybrid control system start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the power switch.

      • If the hybrid control system cannot be started when performing this inspection, the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) may be malfunctioning.

      OK
      Hybrid control system starts.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) Click here

    OK

  4. CHECK WAVE ENVIRONMENT


    1. Install the transmitter battery to the electrical key transmitter sub-assembly.

      Click here

    2. Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (front floor) and perform a entry and start system check.

      Click here

      Note

      Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (front floor).

    3. Bring the electrical key transmitter sub-assembly near the indoor electrical key antenna (rear floor) and perform a entry and start system check.

      Click here

      Tech Tips

      Check that the customize status of the "Ignition Available Area" has been "All".

      Note

      Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the indoor electrical key antenna (rear floor).

      Tech Tips


      • As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

      • If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      • There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

      • If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

      OK
      The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed.
      Result
      Proceed to
      OK
      NG

    OK

    AFFECTED BY WAVE INTERFERENCE

    NG

  5. CHECK FOR DTC


    1. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      OK
      DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    OK

  6. CHECK KEY DIAGNOSTIC MODE


    1. Check the following antennas in key diagnostic mode.


      Body Electrical > Entry&Start > Utility
      Tester Display
      Communication Check(Key Diag Mode)

    2. Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.


      1. A00236KC01
        *a Inspection Point

        Check the No. 2 indoor electrical key antenna assembly (front floor).

        When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

      2. A0022QCC01
        *a Inspection Point

        Check the indoor electrical key antenna (rear floor).

        When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

        Tech Tips


        • Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

        • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

        • It is possible to check which indoor electrical key antenna assembly (front floor or rear floor) is operating by the sounding of the buzzer.

        • When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.

        • When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.

      Result
      Result Proceed to
      The wireless buzzer sounds/does not sound for all indoor electrical key antenna assemblies A
      The wireless buzzer does not sound for only the No. 2 indoor electrical key antenna assembly (front floor) B
      The wireless buzzer does not sound for only the indoor electrical key antenna (rear floor) C

    A

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    C

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INDOOR ELECTRICAL KEY ANTENNA (REAR FLOOR)) Click here

    B

  7. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))


    1. Disconnect the K137 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the K87 No. 2 indoor electrical key antenna assembly (front floor) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K137-21 (CLG5) - K87-1 (ANTE5) Always Below 1 Ω
      K137-20 (CG5B) - K87-3 (CLGB) Always Below 1 Ω
      K137-21 (CLG5) or K87-1 (ANTE5) - Body ground Always 10 kΩ or higher
      K137-20 (CG5B) or K87-3 (CLGB) - Body ground Always 10 kΩ or higher

    4. Reconnect the K137 certification ECU (smart key ECU assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))


    1. A002155C03
      *a

      Front view of wire harness connector

      (to No. 2 indoor Electrical Key Antenna Assembly (Front Floor))
      *b Waveform 1
      *c For 30 seconds after closing any door using the door outside handle
      *d 30 seconds or more have elapsed after closing any door using the door outside handle

      Using an oscilloscope, check the waveform.

      OK
      Tester Connection Condition Tool Setting Specified Condition
      K87-1 (ANTE5) - K87-3 (CLGB)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly not inside vehicle

      3. Within 30 seconds of closing any door using the door outside handle

      		 2 V/DIV., 500 ms/DIV.

      Pulse generation

      (See waveform 1)
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  9. REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)


    1. Temporarily replace the No. 2 indoor electrical key antenna assembly (front floor) with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  10. CHECK KEY DIAGNOSTIC MODE


    1. Check the following antenna in key diagnostic mode.


      Body Electrical > Entry&Start > Utility
      Tester Display
      Communication Check(Key Diag Mode)

    2. Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.


      1. A00236KC01
        *a Inspection Point

        Check the No. 2 indoor electrical key antenna assembly (front floor).

        When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

        Tech Tips


        • Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

        • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

        OK
        Wireless buzzer sounds.
      Result
      Proceed to
      OK
      NG

    OK

    END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  11. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INDOOR ELECTRICAL KEY ANTENNA (REAR FLOOR))


    1. Disconnect the K136 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the Q2 indoor electrical key antenna (rear floor) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K136-15 (CLG6) - Q2-1 (ANTE6) Always Below 1 Ω
      K136-14 (CG6B) - Q2-3 (CLGB) Always Below 1 Ω
      K136-15 (CLG6) or Q2-1 (ANTE6) - Body ground Always 10 kΩ or higher
      K136-14 (CG6B) or Q2-3 (CLGB) - Body ground Always 10 kΩ or higher

    4. Reconnect the K136 certification ECU (smart key ECU assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO INDOOR ELECTRICAL KEY ANTENNA (REAR FLOOR))


    1. A002155C04
      *a

      Front view of wire harness connector

      (to Indoor Electrical Key Antenna (Rear Floor))
      *b Waveform 1
      *c For 30 seconds after closing any door using the door outside handle
      *d 30 seconds or more have elapsed after closing any door using the door outside handle

      Using an oscilloscope, check the waveform.

      OK
      Tester Connection Condition Tool Setting Specified Condition
      Q2-1 (ANTE6) - Q2-3 (CLGB)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly not inside vehicle

      3. Within 30 seconds of closing any door using the door outside handle

      		 2 V/DIV., 500 ms/DIV.

      Pulse generation

      (See waveform 1)
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  13. REPLACE INDOOR ELECTRICAL KEY ANTENNA (REAR FLOOR)


    1. Temporarily replace the indoor electrical key antenna (rear floor) with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  14. CHECK KEY DIAGNOSTIC MODE


    1. Check the following antenna in key diagnostic mode.


      Body Electrical > Entry&Start > Utility
      Tester Display
      Communication Check(Key Diag Mode)

    2. Select either channel 1 or channel 2 and inspect the diagnostic mode for each channel.


      1. A0022QCC01
        *a Inspection Point

        Check the indoor electrical key antenna (rear floor).

        When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

        Tech Tips


        • Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

        • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

        OK
        Wireless buzzer sounds.
      Result
      Proceed to
      OK
      NG

    OK

    END (INDOOR ELECTRICAL KEY ANTENNA (REAR FLOOR) WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)