REAR VIEW MONITOR SYSTEM Image from Camera for Rear View Monitor is Abnormal

DESCRIPTION

The video signals of the rear television camera assembly are transmitted to the radio receiver assembly.

WIRING DIAGRAM

A01D04ME21

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

    Result
    Proceed to
    OK
    NG

    1. Disconnect the K135 radio receiver assembly connector.

    2. Disconnect the T1 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K135-11 (CA+) - T1-6 (CB+) Always Below 1 Ω
      K135-12 (V+) - T1-3 (CV+) Always Below 1 Ω
      K135-24 (V-) - T1-2 (CV-) Always Below 1 Ω
      K135-23 (CGND) - T1-5 (CGND) Always Below 1 Ω
      K135-11 (CA+) - Body ground Always 10 kΩ or higher
      K135-12 (V+) - Body ground Always 10 kΩ or higher
      K135-24 (V-) - Body ground Always 10 kΩ or higher
      K135-23 (CGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT RADIO RECEIVER ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. Reconnect the K135 radio receiver assembly connector.

    2. A01D0QNC01
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K135-24 (V-) - Body ground Always Below 1 Ω
      K135-23 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K135-11 (CA+) - K135-23 (CGND) Power switch on (ACC) 5.5 to 7.05 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  3. INSPECT REAR TELEVISION CAMERA ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. Reconnect the T1 rear television camera assembly connector.

    2. A01CZ51C01
      *a

      Component with harness connected

      (Radio Receiver Assembly)
      A01D0H5C02
      *a

      Component with harness connected

      (Radio Receiver Assembly)
      A0020LAC01
      *a Waveform 1 (camera lens is not covered, displaying an image)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronization Signal
      *d Video Waveform

      Check the waveform of the rear television camera assembly using an oscilloscope.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio receiver assembly with the connector connected.

      OK
      Waveform is similar to that shown in the illustration.
      Item Content
      Measurement terminal K135-12 (V+) - K70-7 (GND1)
      Measurement setting 200 mV/DIV., 50 μs./DIV.
      Condition Power switch on (IG), shift lever in R

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here