TELEMATICS SYSTEM, Diagnostic DTC:B1573, B15CB

DTC Code DTC Name
B1573 Disconnect/Short in Telephone Antenna Circuit
B15CB Telephone Antenna Disconnected

DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Disconnect/Short in Telephone Antenna Circuit

Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the power switch is on (IG).

(Short circuit)

  • Telematics transceiver

  • Roof antenna assembly

  • Instrument panel wire

  • No. 2 antenna cord sub-assembly

  • No. 5 antenna cord assembly
B15CB Telephone Antenna Disconnected

Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the power switch is on (IG).

(Open circuit)

  • Telematics transceiver

  • Roof antenna assembly

  • Instrument panel wire

  • No. 2 antenna cord sub-assembly

  • No. 5 antenna cord assembly

WIRING DIAGRAM

A00224UE14

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click here

PROCEDURE


  1. CHECK DTC


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG) and wait for 20 seconds.

    4. Turn the GTS on.

    5. Check for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Telematics > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. INSPECT ROOF ANTENNA ASSEMBLY


    1. Remove the roof antenna assembly.

      Click here

    2. A0020EGC14
      *a

      Component without harness connected

      (Roof Antenna Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 - 4a Always 4 to 11 kΩ
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ROOF ANTENNA ASSEMBLY Click here

    OK

  3. INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY


    1. Remove the No. 5 antenna cord sub-assembly.

      Click here

    2. A00234MC12
      *a

      Component without harness connected

      (No. 5 Antenna Cord Sub-assembly)
      A0022U4C14
      *a

      Component without harness connected

      (No. 5 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-3 - D-4 Always Below 1 Ω
      C-3a - D-4a Always Below 1 Ω
      C-3 or D-4 - Body ground Always 10 kΩ or higher
      C-3a or D-4a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  4. INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Remove the No. 2 antenna cord sub-assembly.

      Click here

    2. A00219DC15
      *a

      Component without harness connected

      (No. 2 Antenna Cord Sub-assembly)
      A002395C05
      *a

      Component without harness connected

      (No. 2 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-3 - B-3 Always Below 1 Ω
      A-3a - B-3a Always Below 1 Ω
      A-3 or B-3 - Body ground Always 10 kΩ or higher
      A-3a or B-3a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  5. INSPECT INSTRUMENT PANEL WIRE


    1. Disconnect the K161 and K162 instrument panel wire connectors.

    2. A0023ANC08
      *a

      Front view of instrument panel wire connector

      (to Telematics Transceiver)
      A002206C14
      *a

      Front view of instrument panel wire connector

      (to No. 2 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K161-1 (TEL) - K162-3 (TEL) Always Below 1 Ω
      K161-1a - K162-3a Always Below 1 Ω
      K161-1 (TEL) or K162-3 (TEL) - Body ground Always 10 kΩ or higher
      K161-1a or K162-3a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL WIRE

    OK

  6. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here