TELEMATICS SYSTEM, Diagnostic DTC:B15C0, B15C1

DTC Code DTC Name
B15C0 GPS Antenna Disconnected (Short)
B15C1 GPS Antenna Disconnected (Open)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Disconnected (Short)

Current to the roof antenna assembly is lower than the malfunction threshold for 20 seconds when the power switch is on (IG).

(Short circuit)

  • Telematics transceiver

  • Roof antenna assembly

  • Instrument panel wire

  • No. 2 antenna cord sub-assembly

  • No. 5 antenna cord assembly
B15C1 GPS Antenna Disconnected (Open)

Current for roof antenna assembly is higher than the malfunction threshold for 20 seconds when the power switch is on (IG).

(Open circuit)

  • Telematics transceiver

  • Roof antenna assembly

  • Instrument panel wire

  • No. 2 antenna cord sub-assembly

  • No. 5 antenna cord assembly

WIRING DIAGRAM

A00224UE15

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click here

PROCEDURE


  1. CHECK DTC


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG) and wait for 20 seconds.

    4. Turn the GTS on.

    5. Check for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Telematics > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY


    1. Remove the No. 5 antenna cord sub-assembly.

      Click here

    2. A00234MC13
      *a

      Component without harness connected

      (No. 5 Antenna Cord Sub-assembly)
      A0022U4C15
      *a

      Component without harness connected

      (No. 5 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-2 - D-2 Always Below 1 Ω
      C-2a - D-2a Always Below 1 Ω
      C-2 or D-2 - Body ground Always 10 kΩ or higher
      C-2a or D-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY NO.5 Click here

    OK

  3. INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Remove the No. 2 antenna cord sub-assembly.

      Click here

    2. A00219DC16
      *a

      Component without harness connected

      (No. 2 Antenna Cord Sub-assembly)
      A002395C06
      *a

      Component without harness connected

      (No. 2 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 - B-2 Always Below 1 Ω
      A-2a - B-2a Always Below 1 Ω
      A-2 or B-2 - Body ground Always 10 kΩ or higher
      A-2a or B-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY NO.2 Click here

    OK

  4. INSPECT INSTRUMENT PANEL WIRE


    1. Disconnect the K160 and K162 instrument panel wire connectors.

    2. A00209LC10
      *a

      Front view of instrument panel wire connector

      (to Telematics Transceiver)
      A002206C15
      *a

      Front view of instrument panel wire connector

      (to No. 2 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K160-1 (GPS) - K162-2 (GPS) Always Below 1 Ω
      K160-1a - K162-2a Always Below 1 Ω
      K160-1 (GPS) or K162-2 (GPS) - Body ground Always 10 kΩ or higher
      K160-1a or K162-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL WIRE

    OK

  5. REPLACE ROOF ANTENNA ASSEMBLY


    1. Replace the roof antenna assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Telematics > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Telematics > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  6. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here