NAVIGATION SYSTEM Microphone Circuit between Microphone and Navigation Receiver Assembly

DESCRIPTION

The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM

A00220XE02
*a (Shielded)
*b Map Light Assembly (Telephone Microphone Assembly)
*c Radio Receiver Assembly

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. CHECK MICROPHONE (OPERATION CHECK)


    1. A0021OM

      Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

      Click here

    2. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

    3. Push the recording switch and perform voice recording.

      Tech Tips


      • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

      • Voice can be recorded for up to 5 seconds.

    4. Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

      OK
      All check results are normal.
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))


    1. Disconnect the K58 radio receiver assembly connector.

    2. Disconnect the S4 map light assembly (telephone microphone assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K58-49 (SNS2) - S4-1 (SNS2) Always Below 1 Ω
      K58-29 (MACC) - S4-4 (MACC) Always Below 1 Ω
      K58-27 (MIN+) - S4-3 (MCO+) Always Below 1 Ω
      K58-48 (MIN-) - S4-2 (MCO-) Always Below 1 Ω
      K58-49 (SNS2) - Body ground Always 10 kΩ or higher
      K58-29 (MACC) - Body ground Always 10 kΩ or higher
      K58-27 (MIN+) - Body ground Always 10 kΩ or higher
      K58-48 (MIN-) - Body ground Always 10 kΩ or higher
      K58-28 (SGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT RADIO RECEIVER ASSEMBLY


    1. Reconnect the K58 radio receiver assembly connector.

    2. Reconnect the S4 map light assembly (telephone microphone assembly) connector.

    3. A0022IEC02
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K58-29 (MACC) - Body ground Power switch on (ACC) 4 to 6 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K58-28 (SGND) - Body ground Always Below 1 Ω
      K58-48 (MIN-) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  4. INSPECT MAP LIGHT ASSEMBLY


    1. Remove the map light assembly (telephone microphone assembly).

      Click here

    2. A0023AYC21
      *a

      Component without harness connected

      (Map Light Assembly (Telephone Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (SNS2) - 2 (MCO-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 6 Click here

    OK

  5. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    1. Reconnect the K58 radio receiver assembly connector.

    2. Reconnect the S4 map light assembly (telephone microphone assembly) connector.

    3. Turn the power switch on (ACC).

    4. A002201C21
      *a

      Component with harness connected

      (Map Light Assembly (Telephone Microphone Assembly))

      Connect an oscilloscope to terminals 3 (MCO+) and 2 (MCO-) of the S4 map light assembly (telephone microphone assembly) connector.

    5. Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

      Result
      Result Proceed to
      A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output A
      A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output B

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    B

  6. REPLACE TELEPHONE MICROPHONE ASSEMBLY


    1. Replace the telephone microphone assembly.

      Click here

    2. Check if the same malfunction recurs.

      Result
      Result Proceed to
      Malfunction does not recur (returns to normal) A
      Malfunction recurs B

    A

    END

    B

    REPLACE MAP LIGHT ASSEMBLY Click here