NOISE FILTER INSTALLATION

PROCEDURE


  1. INSTALL RADIO SETTING CONDENSER (for Window Defogger)


    1. A0020DS

      Engage the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.

    2. A0021RE

      Engage the 3 claws to install the new terminal cover with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal cover into the condenser.

      • If the terminal cover has been deformed during installation, replace the terminal, terminal cover and condenser with new ones.

    3. Engage the clamp to temporarily install a new radio setting condenser with wire harness.

    4. Install the new radio setting condenser with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Window Defogger)

    w/o Rear Sunshade: Click here

  3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Window Defogger)

    w/ Rear Sunshade: Click here

  4. INSTALL CENTER STOP LIGHT ASSEMBLY WITH COVER (for Window Defogger)

    w/o Rear Sunshade: Click here

  5. INSTALL REAR SEAT SHOULDER BELT HOLE COVER (for Window Defogger)

    Click here

  6. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Window Defogger)

    for Fixed Seat Type: Click here

  7. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for Window Defogger)

    Click here

  8. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for Window Defogger)

    Tech Tips

    Use the same procedure as for the LH side.

  9. INSTALL NO. 3 ROOM PARTITION COVER (for Window Defogger)

    for Fold Down Seat Type: Click here

  10. INSTALL NO. 2 ROOM PARTITION COVER (for Window Defogger)

    for Fold Down Seat Type: Click here

  11. INSTALL NO. 1 ROOM PARTITION COVER (for Window Defogger)

    for Fold Down Seat Type:

    Tech Tips

    Use the same procedure as for the No. 2 room partition cover.

  12. INSTALL REAR SEAT SUB FLOOR PANEL (for Window Defogger)

    for Fold Down Seat Type: Click here

  13. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (for Window Defogger)

    for Fold Down Seat Type: Click here

  14. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for Window Defogger)

    for Fold Down Seat Type: Click here

  15. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (for Window Defogger)

    Click here

  16. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH (for Window Defogger)

    Tech Tips

    Use the same procedure as for the LH side.

  17. INSTALL REAR SEAT SIDE GARNISH RH (for Window Defogger)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  18. INSTALL REAR DOOR SCUFF PLATE RH (for Window Defogger)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  19. INSTALL REAR SEAT ASSEMBLY (for Window Defogger)

    for Fold Down Seat Type: Click here

  20. INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light)


    1. A0022DG

      Engage the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.

    2. A0021IO

      Engage the 6 claws to install the 2 new terminal covers with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal covers into the condenser.

      • If a terminal cover has been deformed during installation, replace the terminal, terminal covers and condenser with new ones.

    3. A0021JE

      Insert the cover as shown in the illustration and engage the claw.

    4. Engage the clamp to temporarily install the new radio setting condenser with wire harness.

    5. Install the new radio setting condenser with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  21. INSTALL REAR SEAT SIDE GARNISH LH

    Click here

  22. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

  23. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

    Click here

  24. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (for Fixed Seat Type)

    Click here

  25. INSTALL REAR SEAT HEADREST ASSEMBLY (for Fixed Seat Type)

    Click here

  26. INSTALL REAR SIDE SEAT BACK ASSEMBLY LH (for Fold Down Seat Type)

    Tech Tips

    Use the same procedure as for the RH side.

    Click here

  27. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  28. INSTALL REAR SEAT CUSHION ASSEMBLY

    Click here

  29. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  30. INSTALL BATTERY SERVICE HOLE COVER LH (w/ Rear Seat Side Airbag)

    Click here

  31. INSPECT SRS WARNING LIGHT (w/ Rear Seat Side Airbag)

    Click here