AUDIO AND VISUAL SYSTEM(w/o Parking Assist Monitor System), Diagnostic DTC:B1563

DTC Code DTC Name
B1563 Haptic Device Disconnected

DESCRIPTION

The radio receiver assembly and remote operation board are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio receiver assembly and remote operation board.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1563 Haptic Device Disconnected A device that is listed in the AVC-LAN network connected device record of the master unit is missing

  • Remote operation board power source circuit

  • AVC-LAN circuit between remote operation board and radio receiver assembly

  • Remote operation board

  • Radio receiver assembly

  • Harness or connector

Tech Tips

The radio receiver assembly is the master unit.

WIRING DIAGRAM

A0021ERE08
*a from Auxiliary Battery
*b Radio Receiver Assembly
*c Remote Operation Board
*d AVC-LAN Communication Line

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components.


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B

        Tech Tips


        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

        • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B

    GO TO STEP 3 Click here

    A

  2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    2. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  4. CHECK HARNESS AND CONNECTOR (REMOTE OPERATION BOARD POWER SOURCE)


    1. Disconnect the K79 remote operation board connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K79-4 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K79-14 (ACC) - K79-4 (GND) Power switch on (ACC) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REMOTE OPERATION BOARD)


    1. Disconnect the K79 remote operation board connector.

    2. Disconnect the K135 radio receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K79-10 (TX+) - K135-18 (TX2+) Always Below 1 Ω
      K79-11 (TX-) - K135-19 (TX2-) Always Below 1 Ω
      K79-10 (TX+) - Body ground Always 10 kΩ or higher
      K79-11 (TX-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. REPLACE REMOTE OPERATION BOARD


    1. Replace the remote operation board.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here