AUDIO AND VISUAL SYSTEM(w/ Parallel Parking Assist Function) Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM


  1. A0020DQE02
    A0021NAE03

PROCEDURE


  1. CHECK SPEAKER (OPERATION CHECK)


    1. A0021I2

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Front No. 3 speaker assembly C
      Rear speaker assembly or rear No. 2 speaker assembly D
      Rear header speaker assembly E
      Rear No. 3 speaker assembly F

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K55 and K56 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - K55-2 (+) Always Below 1 Ω
      P23-28 (FR-) - K55-1 (-) Always Below 1 Ω
      P23-12 (FL+) - K56-2 (+) Always Below 1 Ω
      P23-27 (FL-) - K56-1 (-) Always Below 1 Ω
      P23-13 (FR+) or K55-2 (+) - Body ground Always 10 kΩ or higher
      P23-28 (FR-) or K55-1 (-) - Body ground Always 10 kΩ or higher
      P23-12 (FL+) or K56-2 (+) - Body ground Always 10 kΩ or higher
      P23-27 (FL-) or K56-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the N14 and N29 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-5 (WFR+) - N14-1 Always Below 1 Ω
      P23-20 (WFR-) - N14-2 Always Below 1 Ω
      P23-4 (WFL+) - N29-1 Always Below 1 Ω
      P23-19 (WFL-) - N29-2 Always Below 1 Ω
      P23-5 (WFR+) or N14-1 - Body ground Always 10 kΩ or higher
      P23-20 (WFR-) or N14-2 - Body ground Always 10 kΩ or higher
      P23-4 (WFL+) or N29-1 - Body ground Always 10 kΩ or higher
      P23-19 (WFL-) or N29-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K57 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-7 (CTR+) - K57-2 (+) Always Below 1 Ω
      P23-22 (CTR-) - K57-1 (-) Always Below 1 Ω
      P23-7 (CTR+) or K57-2 (+) - Body ground Always 10 kΩ or higher
      P23-22 (CTR-) or K57-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  8. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the O5 and O10 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-15 (RR+) - O5-3 (+TW) Always Below 1 Ω
      P23-30 (RR-) - O5-1 (-TW) Always Below 1 Ω
      P23-14 (RL+) - O10-3 (+TW) Always Below 1 Ω
      P23-29 (RL-) - O10-1 (-TW) Always Below 1 Ω
      P23-15 (RR+) or O5-3 (+TW) - Body ground Always 10 kΩ or higher
      P23-30 (RR-) or O5-1 (-TW) - Body ground Always 10 kΩ or higher
      P23-14 (RL+) or O10-3 (+TW) - Body ground Always 10 kΩ or higher
      P23-29 (RL-) or O10-1 (-TW) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the O4 and O9 rear speaker assembly connectors.

    2. Disconnect the O5 and O10 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-1 - O5-4 (+) Always Below 1 Ω
      O4-2 - O5-2 (-) Always Below 1 Ω
      O9-1 - O10-4 (+) Always Below 1 Ω
      O9-2 - O10-2 (-) Always Below 1 Ω
      O4-1 or O5-4 (+) - Body ground Always 10 kΩ or higher
      O4-2 or O5-2 (-) - Body ground Always 10 kΩ or higher
      O9-1 or O10-4 (+) - Body ground Always 10 kΩ or higher
      O9-2 or O10-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. Inspect the rear No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  11. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  12. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the P26 and Q40 rear header speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-11 (SR+) - P26-2 Always Below 1 Ω
      P23-26 (SR-) - P26-1 Always Below 1 Ω
      P23-10 (SL+) - Q40-2 Always Below 1 Ω
      P23-25 (SL-) - Q40-1 Always Below 1 Ω
      P23-11 (SR+) or P26-2 - Body ground Always 10 kΩ or higher
      P23-26 (SR-) or P26-1 - Body ground Always 10 kΩ or higher
      P23-10 (SL+) or Q40-2 - Body ground Always 10 kΩ or higher
      P23-25 (SL-) or Q40-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR HEADER SPEAKER ASSEMBLY Click here

  14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the P27 rear No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-6 (WF1+) - P27-1 Always Below 1 Ω
      P23-21 (WF1-) - P27-2 Always Below 1 Ω
      P23-6 (WF1+) or P27-1 - Body ground Always 10 kΩ or higher
      P23-21 (WF1-) or P27-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here