STEERING LOCK SYSTEM, Diagnostic DTC:B2782

DTC Code DTC Name
B2782 Power Source Control ECU Malfunction

DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator assembly) is determined to be abnormal.

Tech Tips

The steering lock ECU (steering lock actuator assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2782 Power Source Control ECU Malfunction

Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the power switch is on (IG).)):


  • The steering lock motor activation command circuit has a short circuit.

  • The steering lock motor activation command circuit has an open circuit.

Tech Tips

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.

  • Steering lock ECU (Steering lock actuator assembly)

  • Certification ECU (Smart key ECU assembly)

  • Harness or connector

 DTC Output Confirmation Operation: Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the power switch off. The steering unlocks when the power switch is turned on (ACC) or on (IG) while carrying the key.)
Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. Prohibits the hybrid control system from being started.
Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2782 - -

WIRING DIAGRAM

A0022ADE38
*a Certification ECU (Smart Key ECU Assembly)
*b Steering Lock ECU (Steering Lock Actuator Assembly)
*c LIN Communication Line

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

    Click here

  • When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

    Click here

  • After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.

    Click here

  • When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).

PROCEDURE


  1. INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the K28 steering lock ECU (steering lock actuator assembly) connector.

    3. A0021T0C37
      *a

      Front view of wire harness connector

      (to Steering Lock ECU (Steering Lock Actuator Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K28-1 (GND) - Body ground Always Below 1 Ω

    4. Reconnect the K28 steering lock ECU (steering lock actuator assembly) connector.

    5. Move the shift lever to P and turn the power switch off.

    6. A0021EQC26
      *a

      Component with harness connected

      (Steering Lock ECU (Steering Lock Actuator Assembly))
      *b Steering Lock Motor not Operating
      *c Steering Lock Motor Operating

      Check the signal waveform according to the condition(s) in the table below.

      Standard Frequency
      Item Content
      Tester Connection K28-3 (IGE) - K28-1 (GND)
      Tool Setting 2 V/DIV., 200 ms./DIV.
      Vehicle Condition Steering lock motor not operating → Operating → Not operating

      Tech Tips


      • When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

      • In order to take measurements when the lock motor is operating, perform either of the following operations:


        • To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).

        • To lock the steering, turn the power switch off with the shift lever in P, and then open a door.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)) Click here

    OK

  2. CLEAR DTC AND DATA LIST MALFUNCTION RECORD


    1. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.

      CAUTION:

      After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK DTC


    1. Perform the DTC output confirmation operation.

    2. Check if DTC B2782 is output.

      Click here


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Result Proceed to
      DTC B2782 is not output. A
      DTC B2782 is output. B

    A

    SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

    B

    REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) Click here

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))


    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Disconnect the K28 steering lock ECU (steering lock actuator assembly) connector.

    3. Disconnect the K137 certification ECU (smart key ECU assembly) connector.

    4. Check for deformation and corrosion of the connector case and terminals.

      OK
      There is no deformation or corrosion of the connector case or terminals.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K28-3 (IGE) - K137-24 (SLR+) Always Below 1 Ω
      K28-3 (IGE) - Body ground Always 10 kΩ or higher
      K137-24 (SLR+) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR