TIRE PRESSURE WARNING SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tech Tips


  • Use the following procedure to troubleshoot the tire pressure warning system.

  • Make sure that the wireless door lock control system has exited diagnostic mode before performing the following procedure.

  • *: Use the GTS.

PROCEDURE


  1. VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

    NEXT

  2. CUSTOMER PROBLEM ANALYSIS


    1. Interview the customer to confirm the problem.

      Tech Tips

      It is important to collect as much specific information as possible from the customer to allow for a quick repair.

      Result
      Result Proceed to
      Tire pressure warning light illuminates A

      w/ Tire Inflation Pressure Display Function:

      Tire pressures are not displayed using tire inflation pressure display function

      		 B

    B

    CHECK TEST MODE DTC Click here

    A

  3. ADJUST TIRE PRESSURE*


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    5. Set the all tire pressure to the specified value.

      Click here

      Note

      Make sure the tires are cool when adjusting the tire pressure.

    6. Display "ID Tire Inflation Pressure" in the Data List and check that the tire pressure values match the adjusted pressure amount.

      Tech Tips

      It may take a few minutes until the values are displayed.

    7. Perform initialization.

      Click here

      Tech Tips

      for ECE-R64 Type:

      The warning threshold value changes depending on the driving conditions during initialization. As a result, the tire pressure warning light may not turn off even if the tire pressure is adjusted to the specified pressure.

      Result
      Result Proceed to
      Tire pressure warning light remains on A
      Tire pressure warning light goes off B

    B

    END

    A

  4. CHECK ECU CONNECTED TO CAN BUS*


    1. Check the ECUs connected to the CAN bus.

      Click here

      Result
      Result Proceed to
      No malfunction appears A
      Malfunction appears B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  5. CHECK FOR DTC (CAN COMMUNICATION SYSTEM)*


    1. Check for DTCs.

      Click here

      Result
      Result Proceed to
      CAN system DTCs are not output A
      CAN system DTCs are output B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  6. CHECK FOR DTC*


    1. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTCs are output A
      DTCs are not output B

    B

    PROBLEM SYMPTOMS TABLE Click here

    A

  7. DTC CHART


    1. Refer to Diagnostic Trouble Code Chart.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 10 Click here

  8. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  9. CIRCUIT INSPECTION*


    1. Refer to Electronic Circuit Inspection Procedure.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  10. REPAIR OR REPLACE


    1. Repair or replace parts based on the diagnosis result.

      Result
      Proceed to
      NEXT

    NEXT

  11. CONFIRMATION TEST*


    1. Check the Data List to confirm that the tire inflation pressure has been received.

      Click here

    2. Perform initialization.

      Click here

    3. Confirm that the initialization has been completed.

      Result
      Proceed to
      NEXT

    NEXT

    END

  12. CHECK TEST MODE DTC


    1. w/ Tire Inflation Pressure Display Function:

      Perform troubleshooting for Test Mode DTC C2197/97.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    END