TIRE AND WHEEL SYSTEM INSPECTION

PROCEDURE


  1. INSPECT TIRES


    1. Inspect the tires for wear and proper inflation pressure.

      Cold Tire Inflation Pressure
      Area Tire Size

      Cold Tire Inflation Pressure

      kPa (kgf/cm2, psi)
      Up to 4 passengers 4 passengers or more
      Front Rear Front Rear
      Australia 225/45RF17 91W

      250 (2.5, 36)*1

      270 (2.7, 39)*2

      250 (2.5, 36)*1

      300 (3.0, 44)*2

      250 (2.5, 36)*1

      270 (2.7, 39)*2

      250 (2.5, 36)*1

      300 (3.0, 44)*2

      225/40R18 88Y

      255/35R18 90Y

      250 (2.5, 36)*1

      270 (2.7, 39)*2

      Europe

      General

      		 205/55R16 91W

      250 (2.5, 36)*1

      250 (2.5, 36)*2

      270 (2.7, 39)*3

      250 (2.5, 36)*1

      270 (2.7, 39)*2

      270 (2.7, 39)*3
      225/45R17 91W

      250 (2.5, 36)*1

      250 (2.5, 36)*2

      250 (2.5, 36)*1

      270 (2.7, 39)*2
      225/45RF17 91W

      225/40R18 88Y

      255/35R18 90Y

      250 (2.5, 36)*1

      250 (2.5, 36)*2
      Russia 225/45RF17 91W

      250 (2.5, 36)*1

      250 (2.5, 36)*2

      250 (2.5, 36)*1

      270 (2.7, 39)*2

      *1: For driving at under 160 km/h (100 mph)

      *2: For driving at over 160 km/h (100 mph)

      *3: With ECO tire pressure label: ECO pressure (for driving at under 160 km/h (100 mph))

    2. A01MT5H

      Using a dial indicator, check the runout of the tires.

      Maximum Tire Runout
      1.0 mm (0.0394 in.)

  2. ROTATE TIRES


    1. A01MSFNC01
      *A except 18 Inch Wheel
      *B for 18 Inch Wheel
      B003XUN Front

      Rotate the tires as shown in the illustration.

      Torque:
      Axle hub nut
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  3. INSPECT AND ADJUST WHEEL BALANCE


    1. A01MRLSC01
      *A for 16 Inch Wheel
      *B except 16 Inch Wheel
      *a 25 mm (0.984 in.)

      Inspect and adjust the off-the-car balance.

      Maximum Imbalance
      8.0 g (0.0176 lb)

      Note


      • Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

      • Do not touch the adhesive surface of the balance weight.

      • Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.

      • Push the balance weight with your finger to securely adhere it to the desired position.

      • Do not reuse balance weights.

      Tech Tips


      • for 16 inch wheel: Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.

      • except 16 inch wheel: Use stick-on type balance weights for both the inner and outer side.

  4. INSPECT FRONT AXLE HUB BEARING

    Click here

  5. INSPECT REAR AXLE HUB BEARING

    Click here