REAR LOWER ARM INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY


    1. for Type A:


      1. Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the bolt, nut and washer.

        Note

        Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

        Tech Tips

        Insert the bolt with the threaded end facing the rear of the vehicle.

    2. for Type B:


      1. Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.

        Note

        Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

        Tech Tips

        Insert the bolt with the threaded end facing the front of the vehicle.

  2. INSTALL REAR LOWER COIL SPRING INSULATOR

    Click here

  3. INSTALL REAR UPPER COIL SPRING INSULATOR

    Click here

  4. INSTALL REAR COIL SPRING

    Click here

  5. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

    Click here

  6. INSTALL REAR STABILIZER LINK ASSEMBLY

    Click here

  7. INSTALL REAR SUSPENSION MEMBER BRACE


    1. Install the rear suspension member brace to the rear suspension member sub-assembly with the 2 bolts.

      Torque:
      56 N*m  { 571 kgf*cm, 41 ft.*lbf }

  8. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

    2. Temporarily install the rear No. 1 suspension arm assembly to the rear axle assembly with the bolt and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

  9. INSTALL TOE CONTROL LINK SUB-ASSEMBLY

    Click here

  10. STABILIZE SUSPENSION

    Click here

  11. INSTALL REAR SHOCK ABSORBER ASSEMBLY

    Click here

  12. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY


    1. for Type A:


      1. Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

        Torque:
        150 N*m  { 1530 kgf*cm, 111 ft.*lbf }

        Note

        Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

    2. for Type B:


      1. Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the bolt.

        Torque:
        150 N*m  { 1530 kgf*cm, 111 ft.*lbf }

        Note

        Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    3. Install the rear No. 2 suspension arm assembly (rear axle assembly side) with the bolt.

      Torque:
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  13. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. Install the rear No. 1 suspension arm assembly (rear suspension member sub-assembly side) with the bolt.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    2. Install the rear No. 1 suspension arm assembly (rear axle assembly side) with the bolt.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  14. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  15. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  16. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  17. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL

    Click here

  18. ADJUST HEADLIGHT AIMING (for HID Headlight)

    Click here

  19. ADJUST HEADLIGHT AIMING (for LED Headlight)

    Click here