REAR SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)


    1. B003YRAC02
      B003XUN Front of the Vehicle
      B003YLR Diluted Liquid Soap

      Apply diluted liquid soap to the outside of a new rear suspension member front body mounting cushion.

      Note

      Do not use grease or undiluted liquid soap. Doing so may cause the rear suspension member front body mounting cushion to slip out.

      Tech Tips

      A 20% liquid soap and water concentration is recommended.

    2. Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.

    3. B003YN1C04
      *a Turn
      *b Hold

      Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

      SST
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011 )
      09950-60021   ( 09951-00910 )
      09570-24011

      Note

      Apply grease to the threads and tip of the SST center bolt before use.

  2. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  3. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side)


    1. B003Y3JC02
      B003XUN Front of the Vehicle
      B003YLR Diluted Liquid Soap

      Apply diluted liquid soap to the outside of a new rear suspension member rear body mounting cushion.

      Note

      Do not use grease or undiluted liquid soap. Doing so may cause the rear suspension member rear body mounting cushion to slip out.

      Tech Tips

      A 20% liquid soap and water concentration is recommended.

    2. Temporarily install the rear suspension member rear body mounting cushion while confirming the installation direction.

    3. B003YN1C05
      *a Turn
      *b Hold

      Using SST, install the rear suspension member rear body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion.

      SST
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011 )
      09950-60021   ( 09951-00910 )
      09570-24011

      Note

      Apply grease to the threads and tip of the SST center bolt before use.

  4. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  5. INSTALL REAR SUSPENSION MEMBER REAR LOWER STOPPER (for LH Side)


    1. Install the rear suspension member rear lower stopper to the rear suspension member sub-assembly.

  6. INSTALL REAR SUSPENSION MEMBER REAR LOWER STOPPER (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  7. INSTALL REAR SUSPENSION MEMBER REAR UPPER STOPPER (for LH Side)


    1. Install the rear suspension member rear upper stopper to the rear suspension member sub-assembly.

  8. INSTALL REAR SUSPENSION MEMBER REAR UPPER STOPPER (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  9. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

    Click here

  10. INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

    Click here

  11. INSTALL REAR STABILIZER BAR

    Click here

  12. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  13. INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  14. INSTALL REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for LH Side)

    Click here

  15. INSTALL REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  16. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. B003YQQC05
      *a Engine Lifter
      *b Attachment
      B003YLR Attachment placement location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools.

      CAUTION:

      Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

      Note


      • Use the attachments to keep the rear suspension member sub-assembly level.

      • The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.

    2. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle body.

      Note

      When raising the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

    3. Install the rear suspension member sub-assembly with the 2 rear suspension member lower stoppers, rear suspension member lower stopper sub-assembly LH, rear suspension member lower stopper sub-assembly RH, 4 bolts (A) and 4 bolts (B).

      Torque:
      Bolt (A)
      127 N*m  { 1295 kgf*cm, 94 ft.*lbf }
      Bolt (B)
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  17. INSTALL REAR BODY MOUNTING CUSHION SUB-ASSEMBLY LH


    1. Install the rear body mounting cushion sub-assembly LH with the 3 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  18. INSTALL REAR BODY MOUNTING CUSHION SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  19. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY

    Click here

  20. INSTALL REAR DRIVE SHAFT ASSEMBLY LH

    Click here

  21. INSTALL REAR DRIVE SHAFT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. INSTALL REAR AXLE ASSEMBLY LH

    Click here

  23. INSTALL REAR AXLE ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  24. CONNECT REAR UPPER CONTROL ARM ASSEMBLY LH


    1. Temporarily install the rear upper control arm assembly LH to the rear axle assembly with the bolt, nut and washer.

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

      Tech Tips

      Insert the bolt with the threaded end facing the rear of the vehicle.

  25. CONNECT REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  26. CONNECT REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for LH Side)


    1. Temporarily install the rear No. 1 upper control arm assembly to the rear axle assembly with the bolt, nut and washer.

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

  27. CONNECT REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  28. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  29. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  30. INSTALL REAR LOWER COIL SPRING INSULATOR (for LH Side)

    Click here

  31. INSTALL REAR LOWER COIL SPRING INSULATOR (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  32. INSTALL REAR UPPER COIL SPRING INSULATOR (for LH Side)

    Click here

  33. INSTALL REAR UPPER COIL SPRING INSULATOR (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  34. INSTALL REAR COIL SPRING LH

    Click here

  35. INSTALL REAR COIL SPRING RH

    Tech Tips

    Perform the same procedure as for the LH side.

  36. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  37. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  38. INSTALL REAR STABILIZER LINK ASSEMBLY LH

    Click here

  39. INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  40. INSTALL REAR SUSPENSION MEMBER BRACE LH

    Click here

  41. INSTALL REAR SUSPENSION MEMBER BRACE RH

    Tech Tips

    Perform the same procedure as for the LH side.

  42. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  43. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  44. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY LH

    Click here

  45. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  46. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 3 parking brake cable assembly to the rear suspension member sub-assembly with the 2 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  47. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tech Tips

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  48. INSTALL PARKING BRAKE ASSEMBLY (for LH Side)

    Click here

  49. INSTALL PARKING BRAKE ASSEMBLY (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  50. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG


    1. Install the 2 parking brake shoe adjusting hole plugs.

  51. INSTALL REAR DISC


    1. Install the 2 rear discs.

      Click here

  52. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  53. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  54. ADJUST PARKING BRAKE

    Click here

  55. TEMPORARILY INSTALL REAR AXLE SHAFT NUT LH

    Click here

  56. TEMPORARILY INSTALL REAR AXLE SHAFT NUT RH

    Tech Tips

    Perform the same procedure as for the LH side.

  57. INSTALL REAR AXLE SHAFT NUT LH

    Click here

  58. INSTALL REAR AXLE SHAFT NUT RH

    Tech Tips

    Perform the same procedure as for the LH side.

  59. INSTALL REAR SPEED SENSOR LH

    Click here

  60. INSTALL REAR SPEED SENSOR RH

    Tech Tips

    Perform the same procedure as for the LH side.

  61. STABILIZE SUSPENSION

    Click here

  62. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH


    1. B003YCI

      Install the rear upper control arm assembly LH (rear axle assembly side) with the nut.

      Torque:
      190 N*m  { 1937 kgf*cm, 140 ft.*lbf }

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

    2. B003Y8J

      Install the rear speed sensor LH to the rear upper control arm assembly LH with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  63. INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  64. INSTALL REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for LH Side)


    1. B003YFX

      Install the rear No. 1 upper control arm assembly (rear axle assembly side) with the nut.

      Torque:
      150 N*m  { 1530 kgf*cm, 111 ft.*lbf }

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

  65. INSTALL REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  66. INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  67. INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  68. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  69. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  70. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  71. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  72. INSTALL TOE CONTROL LINK SUB-ASSEMBLY LH

    Click here

  73. INSTALL TOE CONTROL LINK SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  74. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  75. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

    Click here

  76. INSTALL FRONT CENTER FLOOR BRACE


    1. B003YIS

      Install the front center floor brace with the 6 bolts, 2 nuts and 2 clips.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  77. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY (w/ Cover)


    1. Install the rear No. 2 floor board sub-assembly with the 5 clips and 5 clamps.

  78. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY (w/ Cover)

    Tech Tips

    Perform the same procedure as for the rear No. 2 floor board sub-assembly.

  79. INSTALL ABS MOTOR RELAY


    1. With the power switch off, install the 2 ABS motor relays (ABS motor No. 1 relay and ABS motor No. 2 relay).

    2. Clear the DTCs.

      Click here

  80. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  81. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  82. CHECK FOR SPEED SENSOR SIGNAL

    Click here