REAR AXLE HUB REMOVAL

CAUTION / NOTICE / HINT

Note

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1341, C1342, C1343 and/or C1344 may be stored. As there is no malfunction, clear the DTCs.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE REAR WHEEL

  2. REMOVE ABS MOTOR RELAY

    for LHD: Click here

    for RHD: Click here

  3. SEPARATE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  4. SEPARATE REAR SPEED SENSOR


    1. B003YSI

      Remove the 2 bolts and separate the rear speed sensor from the rear axle carrier sub-assembly.

      Note


      • Prevent foreign matter from contacting the sensor tip.

      • Clean the rear speed sensor installation hole and the contact surfaces every time the rear speed sensor is removed.

  5. REMOVE REAR AXLE SHAFT NUT


    1. B003XV5N08

      Using SST and a hammer, release the staked part of the rear axle shaft nut.

      SST
      09930-00010

      Note

      Loosen the staked part of the nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.

    2. Remove the rear axle shaft nut.

      Tech Tips

      While applying the parking brakes, remove the rear axle shaft nut.

  6. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  7. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  8. REMOVE REAR DISC

    Click here

  9. REMOVE PARKING BRAKE ASSEMBLY

    Click here

  10. SEPARATE TOE CONTROL LINK SUB-ASSEMBLY

    Click here

  11. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. B003XO6

      Remove the bolt and nut, and separate the rear No. 1 suspension arm assembly from the rear axle carrier sub-assembly.

      Note

      Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

  12. REMOVE REAR STABILIZER LINK ASSEMBLY

    Click here

  13. SEPARATE REAR SHOCK ABSORBER ASSEMBLY

    Click here

  14. REMOVE REAR COIL SPRING

    Click here

  15. REMOVE REAR UPPER COIL SPRING INSULATOR

    Click here

  16. REMOVE REAR LOWER COIL SPRING INSULATOR

    Click here

  17. SEPARATE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY

    Click here

  18. LOOSEN REAR UPPER CONTROL ARM ASSEMBLY


    1. B003Y8J

      Remove the bolt and separate the rear speed sensor from the rear upper control arm assembly.

    2. B003YCI

      Loosen the rear upper control arm assembly nut.

      Note


      • Do not remove the bolt and nut.

      • Because the bolt has its own stopper, do not turn the bolt. Loosen the nut with the bolt secured.

  19. REMOVE REAR AXLE ASSEMBLY


    1. B003XRZC02
      *a Matchmark

      Put matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.

    2. Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

      Tech Tips

      If it is difficult to separate the rear drive shaft assembly from the rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.

    3. Remove the bolt, nut and washer and separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

      Note

      Because the bolt has its own stopper, do not turn the bolt. Loosen the nut with the bolt secured.

    4. Remove the rear axle assembly from the rear drive shaft assembly.

      Note

      Be careful not to damage the rear drive shaft boot.

      Tech Tips

      Use wire or an equivalent tool to keep the rear drive shaft assembly.

  20. REMOVE REAR NO. 1 WHEEL BEARING DUST DEFLECTOR


    1. B003YAPC01
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, remove the rear No. 1 wheel bearing dust deflector.

      Note

      Be careful not to damage the rear axle carrier sub-assembly.

  21. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY


    1. Hold the rear axle carrier sub-assembly between aluminum plates in a vise.

      Note

      Do not overtighten the vise.

    2. B003Y16

      Remove the 4 bolts, parking brake plate sub-assembly and rear axle hub and bearing assembly from the rear axle carrier sub-assembly.