HYBRID VEHICLE TRANSMISSION UNIT REASSEMBLY

PROCEDURE


  1. INSTALL OIL STRAINER ASSEMBLY


    1. A0020DH

      Install a new oil strainer assembly to the hybrid vehicle transmission assembly with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. INSTALL OIL COOLER RETURN TUBE


    1. A0021EN

      Install the oil cooler return tube to the hybrid vehicle transmission assembly.

  3. INSTALL TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. A0020ER

      Install the 2 magnets to the transmission oil pan sub-assembly.

    2. Install a new gasket to the transmission oil pan sub-assembly.

    3. A0020UE

      Install the transmission oil pan sub-assembly to the hybrid vehicle transmission assembly with the 18 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

      Tech Tips

      Tighten the bolts in diagonal sequence.

  4. INSTALL TRANSMISSION BREATHER PLUG SUB-ASSEMBLY


    1. A0022BY

      Using a 14 mm union nut wrench, install the transmission breather plug sub-assembly to the hybrid vehicle transmission assembly.

      Torque:
      11.3 N*m  { 115 kgf*cm, 8 ft.*lbf }

  5. INSTALL EXTENSION HOUSING TYPE T OIL SEAL

    Click here

  6. INSTALL FLANGE YOKE ASSEMBLY

    Click here

  7. INSTALL HYBRID VEHICLE TRANSMISSION ASSEMBLY TYPE T OIL SEAL

    Click here

  8. INSTALL ELBOW


    1. Coat 2 new O-ring with ATF and install them to the 2 elbows.

    2. Using SST, install the 2 elbows to the hybrid vehicle transmission assembly so that they are positioned as shown in the illustration.

      A0022IWC01
      *a 27 to 31° *b 22 to 26 °
      *c Length of SST (Nozzle Retaining Nut Wrench) 24 mm (0.945 in.) *d Length of SST (Torque Wrench Adaptor) 200 mm (7.87 in.)
      *e Length of Torque Wrench 180 mm (7.09 in.) - -
      SST
      09268-78010
      Torque:
      without SST [Torque (N*m(kgf*cm, ft.*lbf))]
      35.8 N*m  { 365 kgf*cm, 26 ft.*lbf }
      with SST [Reading of Torque wrench (N*m(kgf*cm, ft.*lbf))]
      15.9 N*m  { 162 kgf*cm, 12 ft.*lbf }

      Tech Tips


      • This torque value is effective when SST is parallel to the torque wrench.

      • The "with SST" torque value is effective when using SST (Nozzle Retaining Nut Wrench) with a fulcrum length of 24 mm (0.945 in.).

      • The "with SST" torque value is effective when using SST (Torque Wrench Adaptor) with a fulcrum length of 200 mm (7.87 in.).

      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 180 mm (7.09 in.).

      • If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

        Click here

  9. INSTALL SHIFT LEVER POSITION SENSOR

    Click here

  10. INSTALL TRANSMISSION CONTROL ROD GROMMET


    1. A0020SUC01
      *1 Spacer
      *2 Transmission Control Rod Grommet

      Install the transmission control rod grommet to the transmission control shaft lever.

    2. Install the spacer to the transmission control rod grommet.

  11. INSTALL TRANSMISSION CONTROL SHAFT LEVER


    1. A0021ES

      Install the transmission control shaft lever to the shift lever position sensor with the spring washer and nut.

      Torque:
      15.7 N*m  { 160 kgf*cm, 12 ft.*lbf }