ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | w/ No. 2 Engine Under Cover | - | - |
| *1 | AIR CLEANER CAP WITH NO. 2 AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | AIR CLEANER HOSE ASSEMBLY |
| *5 | COOL AIR INTAKE DUCT SEAL | *6 | ENGINE UNDER COVER |
| *7 | ENGINE WIRE | *8 | FRONT SUSPENSION MEMBER BRACE |
| *9 | INLET NO. 1 AIR CLEANER | *10 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *11 | NO. 2 ENGINE UNDER COVER | *12 | REAR ENGINE UNDER COVER LH |
| *13 | REAR ENGINE UNDER COVER RH | *14 | AIR CLEANER ASSEMBLY WITH NO. 2 AIR CLEANER HOSE |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *C | Type A | *D | Type B |
| *1 | CONNECTOR COVER ASSEMBLY | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | GENERATOR CABLE | *4 | INLET HEATER WATER HOSE A |
| *5 | OUTLET HEATER WATER HOSE A | *6 | INLET NO. 2 OIL COOLER HOSE |
| *7 | INVERTER TERMINAL COVER | *8 | MOTOR CABLE |
| *9 | NO. 1 COOLER REFRIGERANT DISCHARGE HOSE | *10 | RADIATOR HOSE SUB-ASSEMBLY |
| *11 | NO. 2 FUEL VAPOR FEED HOSE | *12 | NO. 4 RADIATOR HOSE |
| *13 | OUTLET NO. 2 OIL COOLER HOSE | *14 | SUCTION HOSE |
| *15 | NO. 1 RELAY BLOCK COVER | *16 | O-RING |
| *17 | INVERTER MOTOR CABLE BRACKET ASSEMBLY | - | - |
| *a | for Type A: x2 for Type B: x3 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 11 or equivalent | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | ECM | *2 | HEATER WATER PUMP ASSEMBLY |
| *3 | INVERTER RESERVE TANK ASSEMBLY | *4 | NO. 1 INVERTER RESERVE TANK BRACKET |
| *5 | OUTLET NO. 1 HV WATER PUMP PIPE | *6 | NO. 1 WATER HOSE CLAMP BRACKET |
| *7 | NO. 2 INVERTER COOLING HOSE | *8 | NO. 5 INVERTER COOLING HOSE |
| *9 | OUTLET NO. 1 HYBRID WATER PUMP HOSE | *10 | INLET HYBRID WATER PUMP HOSE |
| *11 | NO. 1 INVERTER COOLING HOSE | *12 | INVERTER DRAIN HOSE |
| *13 | NO. 3 INVERTER COOLING HOSE | *14 | INLET HEATER WATER HOSE A |
| *15 | INLET HEATER WATER HOSE B | *16 | NO. 3 ENGINE WIRE |
| *17 | ENGINE WIRE | *18 | WIRE HARNESS |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY WITH TRANSMISSION | *2 | FRONT LOWER BALL JOINT ASSEMBLY LH |
| *3 | FRONT LOWER SUSPENSION MEMBER PROTECTOR | *4 | FRONT UPPER NO. 2 SUSPENSION MEMBER |
| *5 | FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY | *6 | FRONT SHOCK ABSORBER ASSEMBLY LH |
| *7 | STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY | *8 | WIRE HARNESS |
| *9 | NO. 2 EARTH WIRE | *10 | FRONT NO. 2 STABILIZER BRACKET LH |
| *11 | FRONT NO. 2 STABILIZER BRACKET RH | *12 | STRUT BAR BRACKET REINFORCEMENT LH |
| *13 | STRUT BAR BRACKET REINFORCEMENT RH | *14 | REAR ENGINE MOUNTING MEMBER |
| *15 | LEVER | *16 | ENGINE UNDER BRACE SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | w/o EGR System | *B | w/ EGR System |
| *1 | ENGINE OIL LEVEL DIPSTICK | *2 | ENGINE OIL LEVEL DIPSTICK GUIDE |
| *3 | ENGINE WIRE | *4 | EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst) |
| *5 | MANIFOLD STAY | *6 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
| *7 | OIL COOLER WITHOUT HOSE TUBE SUB-ASSEMBLY | *8 | O-RING |
| *9 | GASKET | *10 | NO. 3 EXHAUST MANIFOLD HEAT INSULATOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | HYBRID VEHICLE TRANSMISSION ASSEMBLY | *2 | REAR ENGINE MOUNTING MEMBER |
| *3 | REAR NO. 1 ENGINE MOUNTING INSULATOR | *4 | WIRE HARNESS |
| *5 | MOTOR HEAT INSULATOR | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque |  |
Do not apply lubricants |
ILLUSTRATION
| *A | w/ EGR System | - | - |
| *1 | INLET HEATER WATER HOSE B | *2 | INJECTOR DRIVER |
| *3 | INTAKE MANIFOLD | *4 | PURGE VALVE (PURGE VSV) |
| *5 | NO. 2 EGR PIPE | *6 | OUTLET HEATER WATER HOSE A |
| *7 | THROTTLE BODY WITH MOTOR ASSEMBLY | *8 | NO. 2 FUEL VAPOR FEED HOSE |
| *9 | WATER HOSE SET | *10 | NO. 3 WATER BY-PASS HOSE |
| *11 | NO. 2 WATER BY-PASS HOSE | *12 | THROTTLE BODY GASKET |
| *13 | NO. 2 EGR PIPE GASKET | *14 | WIRE HARNESS CLAMP BRACKET |
| *15 | EGR INLET GASKET | *16 | VENTILATION HOSE ASSEMBLY |
| *17 | GASKET | *18 | INTAKE MANIFOLD STAY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | AIR CONDITIONER HARNESS | *2 | COMPRESSOR WITH MOTOR ASSEMBLY |
| *3 | ENGINE WIRE | *4 | FAN AND GENERATOR V BELT |
| *5 | FLYWHEEL SUB-ASSEMBLY | *6 | FRONT ENGINE MOUNTING INSULATOR |
| *7 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *8 | TRANSMISSION INPUT DAMPER ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ★ | Precoated part |